Rear Power Window RH does not Operate with Rear Power Window Switch RH [04/2013 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Communication RR-Door Motor	Connection status between power window regulator motor assembly (for rear RH door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-

   Body Electrical > Main Body > Data List 

   Tester Display
   Communication RR-Door Motor

   OK

   On the Techstream screen, OK is displayed.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting). Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [04/2013 - ] 

Result: 

OK 

See step  2

1. Enter the following menus: Body Electrical / RR-Door Motor / Data List.
2. Read the Data List according to the display on the Techstream.

   Body Electrical > RR-Door Motor > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   RR Door P/W Up SW	Rear RH door power window manual up switch signal	OFF or ON	OFF: Rear RH door power window manual up switch not being operated ON: Rear RH door power window manual up switch being operated	-
   RR Door P/W Down SW	Rear RH door power window manual down switch signal	OFF or ON	OFF: Rear RH door power window manual down switch not being operated ON: Rear RH door power window manual down switch being operated	-

   Body Electrical > RR-Door Motor > Data List 

   Tester Display
   RR Door P/W Up SW
   RR Door P/W Down SW

   OK

   On the Techstream screen, ON or OFF is displayed accordingly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Enter the following menus: Body Electrical / RR-Door Motor / Active Test.
2. Perform the Active Test according to the display on the Techstream.
   WARNING:

   Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

   Body Electrical > RR-Door Motor > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Power Window	Power window	OFF / DOWN / UP	-

   Body Electrical > RR-Door Motor > Active Test 

   Tester Display
   Power Window

   OK

   Rear RH power window operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [04/2013 - ] 

Result: 

NG 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR). Refer to  REMOVAL [04/2013 - ] 

1. Remove the rear power window regulator switch assembly (for RH door).

   Refer to REMOVAL [04/2013 - ]

2. Inspect the rear power window regulator switch assembly (for RH door).

   Refer to INSPECTION [04/2013 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR). Refer to  REMOVAL [04/2013 - ] 

Result: 

OK 

See step  5

1. Disconnect the O2 power window regulator motor assembly (for rear RH door) connector.
2. Measure the resistance according to the value(s) in the table below.
   STANDARD RESISTANCE
   
   

   Tester Connection	Condition	Specified Condition
   O3-2 (UP) - O2-10 (UP)	Always	Below 1 Ω
   O3-2 (UP) - Body ground	Always	10 kΩ or higher
   O2-10 (UP) - Body ground	Always	10 kΩ or higher
   O3-10 (DOWN) - O2-7 (DOWN)	Always	Below 1 Ω
   O3-10 (DOWN) - Body ground	Always	10 kΩ or higher
   O2-7 (DOWN) - Body ground	Always	10 kΩ or higher
   O3-5 (GND) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR). Refer to  REMOVAL [04/2013 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR