Data List / Active Test [10/2015 - 09/2017]
- DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Powertrain / Radar Cruise / Data List.
- Read the Data List according to the display on the Techstream.
Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Cruise Control Main Switch Cruise control switch signal ON or OFF ON: Cruise control main switch (ON/OFF button) pushed
OFF: Cruise control main switch (ON/OFF button) released- RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off- SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off- Distance Control Switch Distance control switch signal ON or OFF ON: Distance control switch on
OFF: Distance control switch off- Cruise Control Cruise control system operation signal ON or OFF ON: Cruise control system operating
OFF: Cruise control system not operating- Cruise Control Mode Cruise control mode signal All Spd, Hi Spd or Normal All Spd: Vehicle-to-vehicle distance control mode (w/ full-speed following function)
Hi Spd: Vehicle-to-vehicle distance control mode (w/o full-speed following function)
Normal: Constant speed mode- CCS Mem Vehicle Spd Cruise control memorized speed min.: 0 km/h (0 mph), max.: 320 km/h (199 mph) Memorized speed: Cruise control activated - Vehicle Distance Distance to preceding vehicle min.: 0 m (0 ft.), max.: 255 m (836.65 ft.) Actual distance to vehicle - Stop Light SW 1 (M CPU) Stop light switch (Main-CPU) signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Stop Light SW 1 (S CPU) Stop light switch (Sub-CPU) signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Stop Light SW 2 (M CPU) Stop light switch (Main-CPU) signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Vhcl Spd-Brake ECU Vehicle speed min.: -327 km/h (-203 mph), max.: 327 km/h (204 mph) Actual vehicle speed - Vehicle Acceleration Vehicle acceleration min.: -5 m/s2, max.: 5 m/s2 Actual vehicle acceleration - Closed Throttle Position Accelerator pedal idle position signal ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed- Yaw Rate Sensor Yaw rate value min.: -100 deg/s, max.: 100 deg/s Actual yaw rate value - Tar Accel for ACC Target vehicle acceleration for vehicle-to-vehicle distance control mode min.: -5.12 m/s2, max.: 5.08 m/s2 Actual target vehicle acceleration - Tar Accel for CCS Target vehicle acceleration for constant speed mode min.: -5.12 m/s2, max.: 5.08 m/s2 Actual target vehicle acceleration - Request Driving Force Cruise control system request drive force min.: -65536 N, max.: 65534 N Actual request drive force - ECM/PCM Command Origin of the drive force request Pedal, None or DS Pedal: Accelerator pedal depressed
None: drive force not requested
DS: Radar cruise control system operating- Max Val of Available DF Maximum value of available drive force min.: -65536 N, max.: 65534 N Actual available drive force maximum value - Min Val of Available DF Minimum value of available drive force min.: -65536 N, max.: 65534 N Actual available drive force minimum value - Forward Vhcl Relative Spd Vehicle ahead relative speed min.: -128 m/s, max.: 127 m/s Actual vehicle ahead relative speed - Vehicle Approach Warning Forward vehicle approach warning signal ON or OFF ON: Forward vehicle approaching
OFF: Forward vehicle not approaching- Vhcl Stability Ctrl Buzz Skid control buzzer assembly operation signal ON or OFF ON: Skid control buzzer assembly operating
OFF: Skid control buzzer assembly not operating- Forward Vehicle Detect Vehicle ahead detection signal Detect or No Dtct Detect: Vehicle ahead detected
No Dtct: Vehicle ahead not detected- CCS System Check Dynamic radar cruise control system warning indication ON or OFF ON: Dynamic radar cruise control system warning indication (Malfunction detected)
OFF: Dynamic radar cruise control system warning indication (Malfunction not detected)- FRS-Dirt History of dirt detected on millimeter wave radar sensor assembly ON or OFF ON: History of dirt detected on millimeter wave radar sensor assembly
OFF: No history of dirt detected on millimeter wave radar sensor assembly- Bad Wthr Hist (F Radar Sen) History of millimeter wave radar sensor assembly detecting bad weather ON or OFF ON: History of millimeter wave radar sensor assembly detecting bad weather
OFF: No history of millimeter wave radar sensor assembly detecting bad weather- Frnt Radar Sens Temp Hi Millimeter wave radar sensor assembly high temperature abnormality ON or OFF ON: Millimeter wave radar sensor assembly abnormal
OFF: Millimeter wave radar sensor assembly normal- Front Radar Voltage Millimeter wave radar sensor assembly low voltage abnormality Low or Normal Low: Millimeter wave radar sensor assembly abnormal
Normal: Millimeter wave radar sensor assembly normal- CCS Cancel by Low Spd Dynamic radar cruise control system (constant speed mode) low speed cancel signal ON or OFF ON: Low speed cancel signal ON
OFF: Low speed cancel signal OFF- Cancl CCS by Com Delay Dynamic radar cruise control system (constant speed mode) cancel signal ON or OFF ON: Cancel signal ON
OFF: Cancel signal OFF- Cancl CCS by RAM Malfnc Dynamic radar cruise control system (constant speed mode) cancel signal ON or OFF ON: Cancel signal ON
OFF: Cancel signal OFF- A-CCS Cancl-Radar/Wip Dynamic radar cruise control system (vehicle-to-vehicle distance control mode) cancel signal ON or OFF ON: Cancel signal ON
OFF: Cancel signal OFF- Driving Support ECU Destination Variation No Driving support ECU assembly destination variation number Not Available or 0 - Front Radar Sensor Destination Variation No Millimeter wave radar sensor assembly destination variation number Not Available or 0 - Steering Angle Steering angle min.: -3072 deg, max.: 3070.5 deg Actual steering angle - Zero Point Angle Sens Zero point steering angle sensor min.: -3072 deg, max.: 3070.5 deg Actual zero point steering angle - Radar Millimeter wave radar sensor assembly operation signal Emission or Stop Emission: Millimeter wave radar sensor assembly signal sent
Stop: Millimeter wave radar sensor assembly signal stopped- # Codes Number of DTCs min.: 0, max.: 255 Actual number of DTCs - - Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Country# (DSS) Destination country for driving support ECU assembly JPN, NA, EURO, CA, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX Actual country code - - Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
- Read the Data List according to the display on the Techstream.
Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Stop Light Relay Output Stop light control relay (STOP LP) output ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)-
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.
- Perform the Active Test according to the display on the Techstream.
HINT:
The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream.
Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Radar Cruise Approach Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard - Enter the following menus: Body Electrical / Combination Meter / Active Test.
- Perform the Active Test according to the display on the Techstream.
HINT:
The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream.
Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Indicat. Lamp Cruise Cruise control indicator ON or OFF - Indicat. SET Cruise control SET indicator ON or OFF - Indicat. Radar Cruise Radar cruise control indicator ON or OFF - - Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
- Perform the Active Test according to the display on the Techstream.
HINT:
The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream.
Chassis > ABS/VSC/TRAC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Stop Light Relay Stop light control relay (STOP LP) ON or OFF Stop lights come on