How To Proceed With Troubleshooting [10/2015 - ]: Procedure

Result

Result:  1

NEXT 

See step  2

1. Measure the auxiliary battery voltage with the power switch off.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  3

1. Adjust the reflector height.

   Refer to ADJUSTMENT [10/2015 - ]

2. Place the reflector.

   Refer to ADJUSTMENT [10/2015 - ]

3. Connect the Techstream to the DLC3.
4. Turn the power switch on (IG).
5. Turn the Techstream on.
6. Turn the cruise control main switch (ON/OFF) on.
7. Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.
8. Check the amount of misalignment and make a note.
9. Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.
10. Check the amount of misalignment and make a note.

    Result

    Proceed to
    NEXT

Result:  1

NEXT 

See step  4

1. Using the Techstream, check that the CAN communication system is functioning normally.

   Refer to DIAGNOSIS SYSTEM [10/2015 - ]

   Result

   Result	Proceed to
   CAN communication system DTCs are not output	A
   CAN communication system DTCs are output	B

Result:  2

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2015 - ] 

Result:  1

A 

See step  5

Refer to DTC Check / Clear.

DTC CHECK / CLEAR [10/2015 - ]

1. Check for DTCs and note any codes that are output.
2. Clear the DTCs.
3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

   Result

   Result	Proceed to
   DTC does not reoccur	A
   DTC reoccurs	B

Result:  2

B 

GO TO HYBRID CONTROL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] 

Result:  1

A 

See step  6

Refer to DTC Check / Clear.

DTC CHECK / CLEAR [10/2015 - ] 

1. Check for DTCs and note any codes that are output.
2. Clear the DTCs.
3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

   Result

   Result	Proceed to
   DTC does not reoccur	A
   DTC reoccurs	B

Result:  2

B 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2015 - ]  

Result:  1

A 

See step  7

HINT: 

Refer to Problem Symptoms Table.

PROBLEM SYMPTOMS TABLE [10/2015 - ] 

Result

Result:  2

B 

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE 

Result:  1

A 

See step  8

1. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [10/2015 - ] 

2. Operation check

   Refer to OPERATION CHECK [10/2015 - ] 

3. Road test

   Refer to ROAD TEST [10/2015 - ] 

4. Terminals of ECU

   Refer to TERMINALS OF ECU [10/2015 - ] 

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

See step  9

Result

Result:  1

NEXT 

See step  10

Result

Result:  1

NEXT 

END