Front Passenger Side Door Entry Unlock Function does not Operate [09/2014 - ]: Procedure

1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Refer to OPERATION CHECK [09/2014 - ] ).

   OK

   Door locks operate normally.

Result:  NG

NG 

GO TO POWER DOOR LOCK CONTROL SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] )

Result:  OK

OK 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.
   MAIN BODY
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   FR Door Lock Pos	Front RH door unlock detection switch signal / UNLOCK or LOCK	UNLOCK: Front RH door unlocked LOCK: Front RH door locked	-

   OK

   On the Techstream screen, the display changes between LOCK and UNLOCK as shown in the chart above.

Result:  NG

NG 

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) 

(Refer to Door Unlock Detection Switch Circuit [09/2014 - ] )

Result:  OK

OK 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Access / Data List.
5. Read the Data List according to the display on the Techstream.
   SMART ACCESS
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   P-Door Touch Sensor	Front passenger door touch sensor (unlock sensor) / ON or OFF	ON: Front passenger door touch sensor (unlock sensor) touched OFF: Front passenger door touch sensor (unlock sensor) not touched	Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

   OK

   The Techstream display changes correctly in response to the operation of the front door outside handle assembly RH (for front passenger door side).

Result:  OK

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

(Refer to REMOVAL [09/2014 - ] )

Result:  NG

NG 

See step  4

1. Disconnect the Q8 front door outside handle assembly RH (for front passenger door) connector.
2. Disconnect the N94 certification ECU (smart key ECU assembly) connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Q8-4 (SENS) - N94-2 (SEN2)	Always	Below 1 Ω
   N94-1 (E) - Body ground	Always	Below 1 Ω
   Q8-4 (SENS) or N94-2 (SEN2) - Body ground	Always	10 kΩ or higher

Result:  NG

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result:  OK

OK 

See step  5

1. Connect the Q8 front door outside handle assembly RH (for front passenger door) connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   TEXT IN ILLUSTRATION
   
   

   *1	Waveform	-	-
   *a	Component with harness connected (Certification ECU [Smart Key ECU Assembly])	*b	In actuality, sampling is being performed

2. Connect the N94 certification ECU (smart key ECU assembly) connector.
3. Using an oscilloscope, check the waveform.

   OK

   Tester Connection	Switch Condition	Tool Setting	Specified Condition
   N94-2 (SEN2) - N94-1 (E)	Procedure: Power switch off Electrical key transmitter sub-assembly brought outside vehicle All doors locked Electrical key transmitter sub-assembly not sufficiently close to vehicle Front passenger door unlock sensor not touched → touched	2 V/DIV., 500 ms/DIV.	Pulse generation (See waveform)

Result:  OK

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

(Refer to REMOVAL [09/2014 - ] )

Result:  NG

NG 

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH (FOR FRONT PASSENGER DOOR) 

(Refer to DISASSEMBLY [09/2014 - ] )