How To Proceed With Troubleshooting [04/2013 - 09/2020]: Procedure

Result

Result: 

NEXT 

See step  2

Result

Result: 

NEXT 

See step  3

1. Measure the battery voltage.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Use the Techstream to check if the CAN communication system is functioning normally.

   Refer to DIAGNOSIS SYSTEM [04/2013 - 06/2014] , or refer to DIAGNOSIS SYSTEM [06/2014 - 08/2015] , or refer to DIAGNOSIS SYSTEM [08/2015 - 10/2016] , or refer to DIAGNOSIS SYSTEM [10/2016 - 10/2017] , or refer to DIAGNOSIS SYSTEM [10/2017 - 09/2018] , or refer to DIAGNOSIS SYSTEM [09/2018 - 09/2020]

   Result

   Result	Proceed to
   CAN communication system DTCs are not output.	A
   CAN communication system DTCs are output.	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [04/2013 - 10/2016]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2016 - 09/2018]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2018 - ] 

Result: 

A 

See step  5

1. Refer to DTC Check / Clear for the blind spot monitor system.

   Refer to DTC CHECK / CLEAR [04/2013 - 09/2020] 

   Body Electrical > Blind Spot Monitor Master > Trouble Codes 

   Body Electrical > Blind Spot Monitor Slave > Trouble Codes 

2. Record or print DTCs and freeze frame data, if necessary.

   Refer to FREEZE FRAME DATA [04/2013 - 10/2016] , or refer to FREEZE FRAME DATA [10/2016 - 09/2020] 

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [04/2013 - 10/2016]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2016 - 09/2020]  

Result: 

A 

See step  6

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [04/2013 - 08/2015] , or refer to PROBLEM SYMPTOMS TABLE [08/2015 - 10/2016] , or refer to PROBLEM SYMPTOMS TABLE [10/2016 - 10/2017] , or refer to PROBLEM SYMPTOMS TABLE [10/2017 - 09/2020] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table.	A
   Fault is listed in Problem Symptoms Table.	B

   HINT: 

   If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [04/2013 - 06/2014] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2014 - 08/2015] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - 10/2016] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2016 - 10/2017] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2017 - 09/2020]

Result: 

B 

GO TO PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [04/2013 - 08/2015]  , or refer to  PROBLEM SYMPTOMS TABLE [08/2015 - 10/2016]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2016 - 10/2017]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2017 - 09/2020]  

Result: 

A 

See step  7

1. Refer to Terminals of ECU.

   Refer to TERMINALS OF ECU [04/2013 - 10/2016] , or refer to TERMINALS OF ECU [10/2016 - 09/2020] 

2. Refer to Diagnosis System.

   Refer to DIAGNOSIS SYSTEM [04/2013 - 10/2016] , or refer to DIAGNOSIS SYSTEM [10/2016 - 09/2020] 

3. Refer to Data List / Active Test.

   Refer to DATA LIST / ACTIVE TEST [04/2013 - 10/2016] , or refer to DATA LIST / ACTIVE TEST [10/2016 - 09/2020] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

Result

Result: 

NEXT 

See step  9

1. Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).

   Refer to OPERATION CHECK [04/2013 - 10/2016] , or refer to OPERATION CHECK [10/2016 - 09/2020] 

2. Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

Result

Result: 

NEXT 

END