How To Proceed With Troubleshooting [09/2015 - ]: Procedure

Result

Result: 

NEXT 

See step  2

1. Measure the battery voltage.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Adjust the reflector height.

   Refer to ADJUSTMENT [09/2015 - ]

2. Place the reflector.

   Refer to ADJUSTMENT [09/2015 - ]

3. Connect the Techstream to the DLC3.
4. Turn the engine switch on (IG).
5. Turn the Techstream on.
6. Turn the cruise control main switch (ON/OFF) on.
7. Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.
8. Check the amount of misalignment and make a note.
9. Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.
10. Check the amount of offset and make a note.

    Result

    Proceed to
    NEXT

Result: 

NEXT 

See step  4

1. Using the Techstream, check that the CAN communication system is functioning normally.

   OK

   CAN communication system is functioning normally.

   HINT: 

   Refer to CAN Bus Check for the CAN communication system.

   Refer to DIAGNOSIS SYSTEM [09/2015 - 08/2017] , or refer to DIAGNOSIS SYSTEM [08/2017 - 08/2019] , or refer to DIAGNOSIS SYSTEM [08/2019 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - 08/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2020 - ] 

Result: 

OK 

See step  5

Refer to DTC Check / Clear.

Refer to DTC CHECK / CLEAR [09/2015 - ]

1. Check for DTCs and note any codes that are output.
2. Clear the DTCs.
3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

   Result

   Result	Proceed to
   DTC does not reoccur	A
   DTC reoccurs	B

Result: 

B 

GO TO DTC CHART. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - ] 

Result: 

A 

See step  6

Refer to DTC Check / Clear.

Refer to DTC CHECK / CLEAR [09/2015 - 08/2020] , or refer to DTC CHECK / CLEAR [08/2020 - ] 

1. Check for DTCs and note any codes that are output.
2. Clear the DTCs.
3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

   Result

   Result	Proceed to
   DTC does not reoccur	A
   DTC reoccurs	B

Result: 

B 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2015 - 08/2020]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2020 - ]  

Result: 

A 

See step  7

1. Refer to Problem Symptoms Table (Refer to PROBLEM SYMPTOMS TABLE [09/2015 - ] ).

   Result

   Result	Proceed to
   Fault is not listed in problem symptoms table	A
   Fault is listed in problem symptoms table	B

Result: 

B 

See step  8

Result: 

A 

See step  8

1. Terminals of ECU.

   Refer to TERMINALS OF ECU [09/2015 - ] 

2. Data List / Active Test.

   Refer to DATA LIST / ACTIVE TEST [09/2015 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

Result

Result: 

NEXT 

See step  10

Result

Result: 

NEXT 

END