How To Proceed With Troubleshooting [10/2014 - 09/2017]: Procedure

Result

Result: 

NEXT 

See step  2

1. Measure the battery voltage with the engine switch off.

   Standard voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Use the Techstream to check if the CAN communication system is functioning normally.

   Refer to DIAGNOSIS SYSTEM [10/2014 - 09/2017]

   Result

   Result	Proceed to
   CAN communication system DTCs are not output	A
   CAN communication system DTCs are output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 09/2017] 

Result: 

A 

See step  4

1. Use the Techstream to check if the meter / gauge system is functioning normally.

   Refer to DTC CHECK / CLEAR [10/2014 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   Result

   Result	Proceed to
   Meter / gauge system DTCs are not output	A
   Meter / gauge system DTCs are output	B

Result: 

B 

GO TO METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] 

Result: 

A 

See step  5

1. Use the Techstream to check if the vehicle stability control system is functioning normally.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019]

   Chassis > ABS/VSC/TRC > Trouble Codes 

   Result

   Result	Proceed to
   Vehicle stability control system DTCs are not output	A
   Vehicle stability control system DTCs are output	B

Result: 

B 

GO TO VEHICLE STABILITY CONTROL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 05/2019] 

Result: 

A 

See step  6

1. Check for DTCs.

   Refer to DTC CHECK / CLEAR [10/2014 - 09/2015] , or refer to DTC CHECK / CLEAR [09/2015 - 09/2017] 

   Powertrain > Cruise Control > Trouble Codes 

2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [10/2014 - 09/2015] , or refer to DTC CHECK / CLEAR [09/2015 - 09/2017] 

   Powertrain > Cruise Control > Clear DTCs 

3. Recheck for DTCs.

   Refer to DTC CHECK / CLEAR [10/2014 - 09/2015] , or refer to DTC CHECK / CLEAR [09/2015 - 09/2017] 

   Powertrain > Cruise Control > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2014 - 09/2015]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2015 - 09/2016]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2016 - 09/2017]  

Result: 

A 

See step  7

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [10/2014 - 09/2017] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table	A
   Fault is listed in Problem Symptoms Table	B

Result: 

B 

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE 

Result: 

A 

See step  8

1. Terminals of ECU

   Refer to TERMINALS OF ECU [10/2014 - 09/2017] 

2. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [10/2014 - 09/2017] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

Result

Result: 

NEXT 

See step  10

Result

Result: 

NEXT 

END