LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2017 >> RC 300 Base >> Repair and Diagnosis >> Steering >> Steering Column >> Power Tilt & Power Telescopic Steering Column System - Diagnostics - Introduction >> Power Tilt And Power Telescopic Steering Column System >> Data List / Active Test [09/2014 - ] >> Data List / Active Test [09/2014 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [09/2014 - ]

  1. READ DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Turn the engine switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the engine switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.
    6. According to the display on the Techstream, read the Data List.

      Body Electrical > Tilt&Telescopic > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Tilt Position Current tilt position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Position Current telescopic position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Return Position Memorized tilt return position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Return Position Memorized telescopic return position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Memory Pos 1 Tilt data of memory position 1 Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Memory Pos 1 Telescopic data of memory position 1 Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Memory Pos 2 Tilt data of memory position 2 Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Memory Pos 2 Telescopic data of memory position 2 Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Memory Pos 3 Tilt data of memory position 3 Min.: 0
      Max.: 65535      		 28672 to 36864 This item is not related to this vehicle
      Telesco Memory Pos 3 Telescopic data of memory position 3 Min.: 0
      Max.: 65535      		 28672 to 36864 This item is not related to this vehicle
      Tilt Up Limit Uppermost tilt position Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 -
      Tilt Up Limit Position Uppermost tilt position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Down Limit Lowermost tilt position Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 -
      Tilt Down Limit Position Lowermost tilt position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Short Limit Shortest telescopic position Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 -
      Telesco Short Limit Pos Shortest telescopic position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Long Limit Longest telescopic position Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 -
      Telesco Long Limit Pos Longest telescopic position data Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Up Switch Input state of tilt up switch ON or OFF ON: Tilt up switch activated
      OFF: Tilt up switch not activated      		 -
      Tilt Up SW (CAN) Input state of tilt up switch ON or OFF - This item is not related to this vehicle
      Tilt Down Switch Input state of tilt down switch ON or OFF ON: Tilt down switch activated
      OFF: Tilt down switch not activated      		 -
      Tilt Down SW (CAN) Input state of tilt down switch ON or OFF - This item is not related to this vehicle
      Telesco Short Switch Input state of telescopic contract switch ON or OFF ON: Telescopic contract switch activated
      OFF: Telescopic contract switch not activated      		 -
      Telesco Short SW (CAN) Input state of telescopic contract switch ON or OFF - This item is not related to this vehicle
      Telesco Long Switch Input state of telescopic extend switch ON or OFF ON: Telescopic extend switch activated
      OFF: Telescopic extend switch not activated      		 -
      Telesco Long SW (CAN) Input state of telescopic extend switch ON or OFF - This item is not related to this vehicle
      T&T Manual SW Data Voltage data of tilt and telescopic switch Min.: 0.00 V
      Max.: 4.99 V      		 Neutral position: Below 0.20 V
      Tilt up: 1.67 to 2.13 V
      Tilt down: 0.54 to 0.74 V
      Telescopic contract: 1.08 to 1.40 V
      Telescopic extend: 2.22 to 2.77 V      		 -
      S/B Mem1 Tilt and telescopic memory position 1 Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 -
      S/B Mem2 Tilt and telescopic memory position 2 Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 -
      S/B Mem3 Tilt and telescopic memory position 3 Not Mem or Mem Not Mem: Position not memorized
      Mem: Position memorized      		 This item is not related to this vehicle
      T&T Autoaway Function Auto away/return function ON or OFF ON: Auto away/return function allowed
      OFF: Auto away/return function prohibited      		 -
      Power Source Voltage Voltage data of power supply Min.: 0.00 V
      Max.: 19.99 V      		 11.00 to 14.00 V -
      Freeze Speed Info Vehicle speed data Min.: 0 km/h (0 mph)
      Max.: 255 km/h (158 mph)      		 Actual vehicle speed -
      IG Switch (CAN) Communication state of engine switch ON or OFF ON: Communication normal
      OFF: Communication interrupted      		 -
      IG Switch Input state of engine switch ON or OFF ON: Input signal normal
      OFF: Input signal interrupted      		 -
      Receive from Meter Communication state of combination meter assembly signal OK or Interpt OK: Communication normal
      Interpt: Communication interrupted      		 -
      Receive from Seat ECU Communication state of position control ECU and switch assembly LH signal OK or Interpt OK: Communication normal
      Interpt: Communication interrupted      		 -
      Receive from Combination Communication state of combination switch ECU signal OK or Interpt OK: Communication normal
      Interpt: Communication interrupted      		 This item is not related to this vehicle
      J/B Communication state of main body ECU (multiplex network body ECU) signal OK or Interpt OK: Communication normal
      Interpt: Communication interrupted      		 -
      Driver Information 1 Driver Information 1 Not Mem or Mem - -
      Driver 1 Tilt Mem Driver tilt memory position 1 Min.: 0
      Max.: 65535      		 - -
      Driver 1 Telesco Mem Driver telescopic memory position 1 Min.: 0
      Max.: 65535      		 - -
      Driver Information 2 Driver Information 2 Not Mem or Mem - -
      Driver 2 Tilt Mem Driver tilt memory position 2 Min.: 0
      Max.: 65535      		 - -
      Driver 2 Telesco Mem Driver telescopic memory position 2 Min.: 0
      Max.: 65535      		 - -
      Driver Information 3 Driver Information 3 Not Mem or Mem - This item is not related to this vehicle
      Driver 3 Tilt Mem Driver tilt memory position 3 Min.: 0
      Max.: 65535      		 - This item is not related to this vehicle
      Driver 3 Telesco Mem Driver telescopic memory position 3 Min.: 0
      Max.: 65535      		 - This item is not related to this vehicle
      Handle Position Steering wheel position signal Away or Return Away: Steering wheel in away position
      Return: Steering wheel in return position      		 -
      The Number of DTCs Number of stored DTCs Min.: 0
      Max.: 255      		 Actual number of stored DTCs -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Turn the engine switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the engine switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
    6. According to the display on the Techstream, perform the Active Test.

      Body Electrical > Tilt&Telescopic > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Tilt Operation Tilt operation UP/DOWN -
      Telesco Operation Telescopic operation LONG/SHORT -
scientia non olet · About LEMON Manuals