LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2017 >> RC F >> Repair and Diagnosis >> External Pages >> Different car >> Section 18 (Automatic Headlight Beam Level Control System - Diagnostic Codes & Circuit Tests) >> Automatic Headlight Beam Level Control System >> DTC B2452: Abnormal Height Sensor Data at Initialization [03/2019 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC B2452: Abnormal Height Sensor Data at Initialization [03/2019 - ]: Procedure

WARNING: This page is about a different car, the 2024 Lexus RC F, 2023 Lexus RC F, 2022 Lexus RC F, 2021 Lexus RC F, and 2020 Lexus RC F. However, it is still accessible from the selected car via links, so may be relevant.
  1. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  2

  2. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      OK

      DTC B2452 is not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2019 - 09/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2020 - 01/2023]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [01/2023 - ] 

    Result: 

    NG 

    See step  3

  3. CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY 
    1. Check the installation condition of the rear height control sensor sub-assembly.

      OK

      Rear height control sensor sub-assembly is installed correctly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    INSTALL PARTS CORRECTLY. Refer to  INSTALLATION [03/2019 - ] 

    Result: 

    OK 

    See step  4

  4. REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY 
    1. Remove the rear height control sensor sub-assembly.

      Refer to REMOVAL [09/2014 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  6. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      OK

      DTC B2452 is not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END (INITIALIZATION WAS NOT COMPLETED) 

    Result: 

    NG 

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [03/2019 - ] 

scientia non olet · About LEMON Manuals