LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2018 >> IS 350 Base, AWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Front Power Seat Control System (W/ Memory) - Diagnostics - Introduction >> FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) >> Data List / Active Test [04/2013 - ] >> Data List / Active Test [04/2013 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [04/2013 - ]

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Mirror L / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Mirror L > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Seat Memory Switch1 M1 switch ON or OFF ON: M1 switch on
      OFF: M1 switch off      		 -
      Seat Memory Switch2 M2 switch ON or OFF ON: M2 switch on
      OFF: M2 switch off      		 -
      Seat Memory Switch3 M3 switch ON or OFF ON: M3 switch on
      OFF: M3 switch off      		 -
      Seat Memory Set SW SET switch ON or OFF ON: SET switch on
      OFF: SET switch off      		 -
      +B Voltage Input Value Power supply for outer mirror control ECU assembly (driver door) Min: 0, Max: 25.5 Within range from 11 to 14 V -
    6. Enter the following menus: Body Electrical / Driver Seat / Data List.
    7. Read the Data List according to the display on the Techstream.

      Body Electrical > Driver Seat > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Reclining Rear Reclining switch signal (Rearward) ON or OFF ON: Reclining switch (Rearward) on
      OFF: Reclining switch (Rearward) off      		 -
      Reclining Front Reclining switch signal (Forward) ON or OFF ON: Reclining switch (Forward) on
      OFF: Reclining switch (Forward) off      		 -
      Front Vertical Down Front vertical switch signal (Downward) ON or OFF ON: Front vertical switch (Downward) on
      OFF: Front vertical switch (Downward) off      		 -
      Front Vertical Up Front vertical switch signal (Upward) ON or OFF ON: Front vertical switch (Upward) on
      OFF: Front vertical switch (Upward) off      		 -
      Lifter Switch Down Lifter switch signal (Downward) ON or OFF ON: Lifter switch (Downward) on
      OFF: Lifter switch (Downward) off      		 -
      Lifter Switch Up Lifter switch signal (Upward) ON or OFF ON: Lifter switch (Upward) on
      OFF: Lifter switch (Upward) off      		 -
      Slide Rear Slide switch signal (Rearward) ON or OFF ON: Slide switch (Rearward) on
      OFF: Slide switch (Rearward) off      		 -
      Slide Front Slide switch signal (Forward) ON or OFF ON: Slide switch (Forward) on
      OFF: Slide switch (Forward) off      		 -
      Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Seat Memory No3 Seat position memorized with M3 switch Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Ignition Switch Communication state of engine switch signal ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off or on (ACC)      		 -
      P Switch Park state signal ON or OFF ON: Shift lever in P
      OFF: Shift lever in a position other than P      		 -
      Parking Brake SW Parking brake switch status ON or OFF ON: Parking brake applied
      OFF: Parking brake released      		 -
      Vehicle Speed Vehicle speed data Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
      Power Voltage Power supply for front power seat switch LH Min: 0.95 V, Max: 20.84 V Within range from 11 to 14 V -
      Slide Position Seat sliding position Min: 0, Max: 65535 Within range from 0 to 65535 -
      Reclining Position Seat reclining position Min: 0, Max: 65535 Within range from 0 to 65535 -
      Front Vertical Position Seat front vertical position Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Position Seat lifter position Min: 0, Max: 65535 Within range from 0 to 65535 -
      Slide Pos Mem No1 Seat slide position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Reclining Pos Mem No1 Seat reclining position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Frnt Vrtcl Pos Mem No1 Front vertical position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Pos Mem No1 Lifter position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Slide Pos Mem No2 Seat slide position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Reclining Pos Mem No2 Seat reclining position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Frnt Vrtcl Pos Mem No2 Front vertical position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Pos Mem No2 Lifter position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Slide Pos Mem No3 Seat slide position memorized with M3 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Reclining Pos Mem No3 Seat reclining position memorized with M3 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Frnt Vrtcl Pos Mem No3 Front vertical position memorized with M3 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Pos Mem No3 Lifter position memorized with M3 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Initialize Flag Seat lifter limit position memory ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Front Vertical Init Flag Seat front vertical limit position memory ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Reclining Position Init Flg Seat reclining limit position memory ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Slide Position Init Flag Seat slide limit position memory ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Slide Position Front Limit Seat slide limit position (front) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Slide Position Rear Limit Seat slide limit position (rear) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Reclining Position Front Limit Seat reclining limit position (front) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Reclining Position Rear Limit Seat reclining limit position (rear) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Front Vertical UP Limit Seat front vertical limit position (up) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Front Vertical Down Limit Seat front vertical limit position (down) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Position UP Limit Seat lifter limit position (up) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Lifter Position Down Limit Seat lifter limit position (down) Min: 0, Max: 65535 Within range from 0 to 65535 -
      Memory Button Buzzer Request Driver seat buzzer request display OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT OFF: Buzzer does not sound
      MOVE: Request to sound buzzer when starting memory replay
      REGISTRY: Request to sound buzzer when starting memory registration
      CANCEL: Request to sound buzzer when canceling memory call registration
      REG NG: Request to sound buzzer when memory call registration not possible
      REG WAIT: Request to sound buzzer when starting memory call cabin scan      		 -
      Driver Seat Request Command Driver seat operation request received OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET OFF: No instruction
      MEMORY: Request to memorize
      MEM MOV: Request to recall memory
      MEM SOD: Request to replay
      RET MOV: Request to return
      AWY MOV: Request to move away
      AWY SOD: Request to recall away position memory
      MEM AWY: Request to recall memorized position of seatback
      MEM RET: Request to restore seatback to memorized position      		 -
      Driver Seat POS REQ Seat memory switch LH operation value OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3 OFF: No operation
      MEM1: M1 switch operation status
      MEM2: M2 switch operation status
      MEM3: M3 switch operation status
      DRV1: Other 1 operation status
      DRV2: Other 2 operation status
      DRV3: Other 3 operation status      		 -
      Away Move Range Scale The seat travel distance for the power easy access system NONE, SMALL, STANDRD or LONG NONE: Seat travel distance none
      SMALL: Seat travel distance short
      STANDRD: Seat travel distance normal
      LONG: Seat travel distance long      		 -
      Return Move Return function NOT AVL or AVAIL NOT AVL: Not available
      AVAIL: Available      		 -
      Return & Away Function Return & away function NOT AVL or AVAIL NOT AVL: Not available
      AVAIL: Available      		 -
      Driver Seat Buckle SW Driver seat belt buckle switch ON or OFF ON: Driver seat belt fastened
      OFF: Driver seat belt unfastened      		 -
      Return Position Return position Min: 0, Max: 65535 Within range from 0 to 65535 -
      Shift SW Position Park state signal* Shift P or Shift Other Shift P: Shift lever in P
      Shift Other: Shift lever in a position other than P      		 Not applicable
      Number of Trouble Codes Number of trouble codes Min: 0 or Max: 255 Number of DTCs will be displayed -
      1. *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
    8. Enter the following menus: Body Electrical / Main Body / Data List.
    9. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FL Door Courtesy SW Front door courtesy light switch assembly (driver door) signal ON or OFF ON: Driver door open
      OFF: Driver door closed      		 -
      Seat Move Distance Setting of the customized item "Seat Move Distance" OFF, Little or Standard Customized value displayed -
      Seat position/Tilt & Telesco memory recall setting Setting of the customized item "Seat position/Tilt & Telesco memory recall setting" D Door or Any Door Customized value displayed -
      Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID1
      MEM SW1: M1 switch linked with key ID1
      MEM SW2: M2 switch linked with key ID1
      MEM SW3: M3 switch linked with key ID1      		 -
      Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID2
      MEM SW1: M1 switch linked with key ID2
      MEM SW2: M2 switch linked with key ID2
      MEM SW3: M3 switch linked with key ID2      		 -
      Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID3
      MEM SW1: M1 switch linked with key ID3
      MEM SW2: M2 switch linked with key ID3
      MEM SW3: M3 switch linked with key ID3      		 -
      Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID4
      MEM SW1: M1 switch linked with key ID4
      MEM SW2: M2 switch linked with key ID4
      MEM SW3: M3 switch linked with key ID4      		 -
      Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID5
      MEM SW1: M1 switch linked with key ID5
      MEM SW2: M2 switch linked with key ID5
      MEM SW3: M3 switch linked with key ID5      		 -
      Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID6
      MEM SW1: M1 switch linked with key ID6
      MEM SW2: M2 switch linked with key ID6
      MEM SW3: M3 switch linked with key ID6      		 -
      Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3 NONE: No switches linked with key ID7
      MEM SW1: M1 switch linked with key ID7
      MEM SW2: M2 switch linked with key ID7
      MEM SW3: M3 switch linked with key ID7      		 -
      Driver Seat Memory1 Seat position memorized with M1 switch ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Driver Seat Memory2 Seat position memorized with M2 switch ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Driver Seat Memory3 Seat position memorized with M3 switch ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      D Seat Configuration Front power seat switch LH status NONE, Not RTN or Return NONE: Front power seat switch LH not connected
      Not RTN: Front power seat switch LH connected (Not including power seat power easy access system function)
      Return: Front power seat switch LH connected (Including power seat power easy access system function)      		 -
      Communication P-Seat Connection status between front power seat switch RH and main body ECU (multiplex network body ECU)* STOP or OK STOP: Communication stopped
      OK: Normal communication      		 Not applicable
      Communication D-Seat Connection status between front power seat switch LH and main body ECU (multiplex network body ECU) STOP or OK STOP: Communication stopped
      OK: Normal communication      		 -
      1. *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
    10. Enter the following menus: Body Electrical / Master Switch / Data List.
    11. Read the Data List according to the display on the Techstream.

      Body Electrical > Master Switch > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Door Lock Switch Status Door control switch (multiplex network master switch assembly) lock signal ON or OFF ON: Lock side of door control switch (multiplex network master switch assembly) pushed
      OFF: Lock side of door control switch (multiplex network master switch assembly) not pushed      		 -
      Door Unlock Switch Status Door control switch (multiplex network master switch assembly) unlock signal ON or OFF ON: Unlock side of door control switch (multiplex network master switch assembly) pushed
      OFF: Unlock side of door control switch (multiplex network master switch assembly) not pushed      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.
    5. Perform the Active Test according to the display on the Techstream.

      Body Electrical > Driver Seat > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Seat Reclining Seat reclining operation OFF/Rear/Front -
      Front Vertical Operation Seat front vertical operation OFF/Down/Up -
      Lifter Operation Seat lifter operation OFF/Down/Up -
      Seat Slide Operation Seat slide operation OFF/Rear/Front -
      Buzzer Buzzer operation OFF/ON -
scientia non olet · About LEMON Manuals