How To Proceed With Troubleshooting [11/2021 - 10/2023]: Procedure

Result

Result: 

NEXT 

See step  2

1. Measure the auxiliary battery voltage with the power switch off.

   Standard voltage

   11 to 14 V

   If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

2. Check the fuses and relays.
3. Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Check if the CAN communication system is functioning normally.

   HINT: 

   Refer to CAN Bus Check in CAN Communication System.

   Refer to DIAGNOSIS SYSTEM [11/2021 - 10/2022] , or refer to DIAGNOSIS SYSTEM [10/2022 - 10/2023]

   OK

   CAN communication system is functioning normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - 10/2023] 

Result: 

OK 

See step  4

HINT: 

Refer to DTC Check / Clear.

Refer to DTC CHECK / CLEAR [11/2021 - ]

1. Turn the power switch on (IG) and wait for at least 5 minutes.
2. Check for DTCs.

   Body Electrical > Ethernet Switch1 > Trouble Codes 

   Body Electrical > Ethernet Switch2 > Trouble Codes 

   Result

   Result	Proceed to
   No DTCs output from Ethernet switch 1 and Ethernet switch 2	A
   DTC output from Ethernet switch 1 or Ethernet switch 2	B

Result: 

B 

GO TO ETHERNET COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - 10/2023] 

Result: 

A 

See step  5

HINT: 

Refer to DTC Check / Clear.

Refer to DTC CHECK / CLEAR [11/2021 - ] 

1. Check for DTCs and note any codes that are output.

   Body Electrical > Spatial Information Service > Trouble Codes 

2. Clear the DTCs.

   Body Electrical > Spatial Information Service > Clear DTCs 

3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

   Body Electrical > Spatial Information Service > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2021 - 10/2023]  

Result: 

A 

See step  6

1. Check for vehicle control history (RoB) and note any codes that are output.

   Body Electrical > Spatial Information Service > Utility 

   Tester Display
   Vehicle Control History (RoB)

2. If the vehicle control history (RoB) is output, record it.

   Result

   Result	Proceed to
   Vehicle control history (RoB) is not output	A
   Vehicle control history (RoB) is output	B

Result: 

B 

GO TO VEHICLE CONTROL HISTORY (RoB). Refer to  VEHICLE CONTROL HISTORY (RoB) [11/2021 - 10/2022]  , or refer to  VEHICLE CONTROL HISTORY (RoB) [10/2022 - 10/2023] 

Result: 

A 

See step  7

1. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [11/2021 - ] 

2. Terminals of ECU

   Refer to TERMINALS OF ECU [11/2021 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

Result

Result: 

NEXT 

See step  9

Result

Result: 

NEXT 

END