Data List / Active Test [03/2019 - ]
- DATA LIST NOTE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / HL AutoLeveling / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Headlight Low Beam State Low beam headlight state OFF or ON OFF: Low beam headlights off
ON: Low beam headlights on- Headlight High Beam State High beam headlight state OFF or ON OFF: High beam headlights off
ON: High beam headlights on- DRL Operating State Daytime running light state OFF or ON OFF: Daytime running lights off
ON: Daytime running lights on- Clearance Light State Parking light state OFF or ON OFF: Parking lights off
ON: Parking lights on- Right Cornering Light State Cornering light RH state OFF or ON OFF: Cornering light RH off
ON: Cornering light RH onAlthough this item is displayed on the Techstream, it is not applicable to this vehicle. Left Cornering Light State Cornering light LH state OFF or ON OFF: Cornering light LH off
ON: Cornering light LH onAlthough this item is displayed on the Techstream, it is not applicable to this vehicle. +B Headlight ECU sub-assembly LH IG power supply voltage value 0.00 to 19.75 V 11.00 to 14.00 V - Height Sens Pw Supply Val Rear height control sensor sub-assembly power supply value 0.00 to 5.00 V 4.61 to 5.00 V - Rr Height Sens Signal Val Rear height control sensor sub-assembly signal value 0.00 to 5.00 V 0.50 to 4.50 V Value changes according to vehicle height Front Right Wheel Speed Value Front right wheel speed 0.00 to 260.00 km/h (162.00 mph) Condition can be displayed - Front Left Wheel Speed Value Front left wheel speed 0.00 to 260.00 km/h (162.00 mph) Condition can be displayed - Vehicle Speed Vehicle speed 0.00 to 260.00 km/h (162.00 mph) Condition can be displayed - Rear Height Adjust Value Rear height adjustment off set value 0 to 1023 Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed) - Rear Height Adjust Valid Flag Rear height adjustment range Inval or Valid Inval: Rear height control sensor sub-assembly value out of normal range
Valid: Rear height control sensor sub-assembly value within normal range- Init Writing Count Number of times initialization performed 0 to 255 Number of times initialization performed - Sensor Initialization Hist Sensor initialization history not comp, 10%, 25%, 50%, 75%, 100% or complied not comp: Headlight ECU sub-assembly LH not initialized after replacing
10%: Initialization completed when fuel tank was 10% full
25%: Initialization completed when fuel tank was 25% full
50%: Initialization completed when fuel tank was 50% full
75%: Initialization completed when fuel tank was 75% full
100%: Initialization completed when fuel tank was 100% full
complied: ECU not replaced and ECU has not been initialized at workshop- Steering Sensor Signal Steering angle sensor value -384.0 to 382.5 deg Changes according to the operation of the steering wheel - Steering Sensor Center Position Steering sensor center position -3072.0 to 3070.5 deg 0.0 deg - +B Voltage Value Headlight ECU sub-assembly LH IG power supply voltage value 0.00 to 19.75 V 11.00 to 14.00 V - Leveling Motor Target Position Headlight leveling motor target position 0.0 to 102.3% 10 to 90% - Number Of Trouble Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
- Perform the Active Test according to the display on the Techstream.
Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Drive The Leveling Motor Leveling motor upward or downward operation Stop/Down/Up Perform the Active Test with the engine started and vehicle stopped Headlight Leveling Indicator "Headlight System Malfunction Visit Your Dealer" display OFF or ON -