LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2019 >> LC 500 >> Repair and Diagnosis >> External Pages >> Different car >> Section 108 (Lighting System (Ext) - Service Information) >> Rear Combination Light Assembly >> Installation [08/2015 - 10/2016] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation [08/2015 - 10/2016]: Procedure

WARNING: This page does not describe the selected car, but rather 27 other vehicles, including the 2024 Lexus IS 500, 2024 Lexus IS 350, 2024 Lexus IS 300, 2023 Lexus IS 500, and 2023 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY 
    1. Engage the grommet.
    2. Connect the connector to install the rear combination light socket and wire sub-assembly.
  2. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH 

    Refer to PROCEDURE - Step 5

  3. INSTALL LUGGAGE COMPARTMENT TRIM COVER RH (for RH Side) 

    Refer to PROCEDURE - Step 4

  4. INSTALL FRONT UPPER LUGGAGE COMPARTMENT TRIM COVER 

    Refer to PROCEDURE - Step 6

  5. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 2

  6. INSTALL NO. 2 ROOM PARTITION COVER 

    Refer to PROCEDURE - Step 10

  7. INSTALL REAR SEAT SUB FLOOR PANEL 

    Refer to PROCEDURE - Step 12

  8. INSTALL REAR SEAT ASSEMBLY 

    Refer to INSTALLATION [04/2013 - 10/2016]

  9. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER 

    Refer to PROCEDURE - Step 12

  10. INSTALL REAR LUGGAGE COMPARTMENT TRIM COVER 

    Refer to PROCEDURE - Step 13

  11. INSTALL DECK SIDE TRIM BOX RH 

    Refer to PROCEDURE - Step 14

  12. INSTALL DECK SIDE TRIM BOX LH 

    Refer to PROCEDURE - Step 15

  13. INSTALL SPARE WHEEL COVER TRAY LH 

    Refer to PROCEDURE - Step 17

  14. INSTALL SPARE WHEEL COVER TRAY RH 

    Refer to PROCEDURE - Step 16

  15. INSTALL LUGGAGE COMPARTMENT FLOOR MAT 

    Refer to PROCEDURE - Step 18

  16. INSTALL REAR BUMPER UPPER RETAINER 
    1. Engage the guide.
    2. Install the rear bumper upper retainer with the screw.
    3. Engage the clamp.
  17. INSTALL REAR BUMPER ASSEMBLY 

    Refer to INSTALLATION [04/2013 - 10/2016]

  18. INSTALL REAR TURN SIGNAL LIGHT BULB 
    1. Install the rear turn signal light bulb to the rear combination light socket and wire sub-assembly.
  19. INSTALL REAR COMBINATION LIGHT ASSEMBLY 
    1. Connect the connector.
    2. Turn the cap as shown in the illustration to connect it.
      GTY464806Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cap
    3. Turn the rear combination light socket and wire sub-assembly with the rear turn signal light bulb as shown in the illustration to connect them as a unit.
      GTY461356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Engage the 3 guides and pin to temporarily install the rear combination light assembly as shown in the illustration.
      GTY467948Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin
      *b Guide
    5. Install the rear combination light assembly with the 2 screws.

      Torque: 2.2 N*m (22 kgf*cm, 19 in.*lbf) 

    6. Remove the protective tape.
  20. INSTALL REAR LIGHT COVER 
    1. Engage the 6 claws to install the 2 rear light covers.
      GTY467796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals