Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [10/2014 - ]: Procedure

1. Read the Data List according to the display on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [10/2014 - ]

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Communication P-Door Motor	Connection status between power window regulator motor assembly LH (for front passenger door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-

   Body Electrical > Main Body > Data List 

   Tester Display
   Communication P-Door Motor

   OK

   On the Techstream screen, OK is displayed.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO LIN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] 

Result: 

OK 

See step  2

1. Read the Data List according to the display on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [10/2014 - ]

   Body Electrical > P-Door Motor > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   P Door P/W Up SW	Front passenger door power window manual up switch signal	OFF or ON	OFF: Front passenger door power window manual up switch not being operated ON: Front passenger door power window manual up switch being operated	-
   P Door P/W Down SW	Front passenger door power window manual down switch signal	OFF or ON	OFF: Front passenger door power window manual down switch not being operated ON: Front passenger door power window manual down switch being operated	-

   Body Electrical > P-Door Motor > Data List 

   Tester Display
   P Door P/W Up SW
   P Door P/W Down SW

   OK

   On the Techstream screen, ON or OFF is displayed accordingly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Perform the Active Test according to the display on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [10/2014 - ]

   WARNING:

   Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

   Body Electrical > P-Door Motor > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Power Window	Power window	OFF / DOWN / UP	-

   Body Electrical > P-Door Motor > Active Test 

   Tester Display
   Power Window

   HINT: 

   Up and down movement does not occur if the arrow is not pressed and held.

   OK

   Front passenger door power window operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [10/2014 - 05/2019]  , or refer to  REMOVAL [05/2019 - ] 

Result: 

NG 

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [10/2014 - 05/2019]  , or refer to  REMOVAL [05/2019 - ] 

1. Remove the power window regulator switch assembly.

   Refer to REMOVAL [10/2014 - ]

2. Inspect the power window regulator switch assembly.

   Refer to INSPECTION [10/2014 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to  REMOVAL [10/2014 - ] 

Result: 

OK 

See step  5

1. Disconnect the L11 power window regulator switch assembly connector.
2. Disconnect the L2 front power window regulator motor assembly RH connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L11-5 (UP) - L2-10 (UP)	Always	Below 1 Ω
   L11-4 (DOWN) - L2-7 (DOWN)	Always	Below 1 Ω
   L11-7 (GND) - Body ground	Always	Below 1 Ω
   L11-5 (UP) or L2-10 (UP) - Body ground	Always	10 kΩ or higher
   L11-4 (DOWN) or L2-7 (DOWN) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [10/2014 - 05/2019]  , or refer to  REMOVAL [05/2019 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR