How To Proceed With Troubleshooting [09/2015 - 12/2017]: Procedure

Result

Result: 

NEXT 

See step  2

1. Measure the battery voltage.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Using the Techstream, check that the CAN communication system is functioning normally.

   HINT: 

   Refer to CAN Bus Check in CAN Communication System.

   Refer to DIAGNOSIS SYSTEM [09/2015 - 08/2016] , or refer to DIAGNOSIS SYSTEM [08/2016 - 12/2017]

   OK

   CAN communication system is functioning normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - ] 

Result: 

OK 

See step  4

1. Use the Techstream to check if the meter / gauge system is functioning normally.

   Refer to DTC CHECK / CLEAR [09/2015 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   Result

   Result	Proceed to
   Meter / gauge system DTCs are not output	A
   Meter / gauge system DTCs are output	B

Result: 

B 

GO TO METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - ] 

Result: 

A 

See step  5

1. Use the Techstream to check if the vehicle stability control system is functioning normally.

   Refer to DTC CHECK / CLEAR [09/2015 - 08/2019]

   Chassis > ABS/VSC/TRAC/EPB > Trouble Codes 

   Result

   Result	Proceed to
   Vehicle stability control system DTCs are not output	A
   Vehicle stability control system DTCs are output	B

Result: 

B 

GO TO VEHICLE STABILITY CONTROL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - 08/2019] 

Result: 

A 

See step  6

1. Check for DTCs, and note down any DTCs that are output.

   Refer to DTC CHECK / CLEAR [09/2015 - 12/2017] 

   Powertrain > Cruise Control > Trouble Codes 

2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [09/2015 - 12/2017] 

   Powertrain > Cruise Control > Clear DTCs 

3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

   Refer to DTC CHECK / CLEAR [09/2015 - 12/2017] 

   Powertrain > Cruise Control > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2015 - 12/2017]  

Result: 

A 

See step  7

HINT: 

Refer to Problem Symptoms Table.

Refer to PROBLEM SYMPTOMS TABLE [09/2015 - 08/2016] , or refer to PROBLEM SYMPTOMS TABLE [08/2016 - 12/2017] 

Result

Result: 

B 

See step  9

Result: 

A 

See step  8

1. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [09/2015 - 12/2017] 

2. Road test

   Refer to ROAD TEST [09/2015 - 12/2017] 

3. Terminals of ECU

   Refer to TERMINALS OF ECU [09/2015 - 12/2017] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

Result

Result: 

NEXT 

See step  10

Result

Result: 

NEXT 

END