Installation [08/2019 - ]: Procedure

INSTALL STEERING COLUMN ASSEMBLY

NOTE:

Make sure that the wire harness is not interfering with the steering column assembly.

Install the steering column assembly with the bolt and 2 nuts.
Torque: 36 N*m (367 kgf*cm, 27 ft.*lbf)
Connect each connector and engage each wire harness clamp to the steering column assembly.

Connect the 2 connectors.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Matchmark

Install the steering intermediate shaft assembly to the steering column assembly.
Install a new bolt.
Torque: 64 N*m (653 kgf*cm, 47 ft.*lbf)

Tighten the bolt.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
Refer to PROCEDURE - Step 13 [10/2015 - ]
INSTALL STOP LIGHT SWITCH ASSEMBLY
Refer to PROCEDURE - Step 1 [10/2015 - ]

INSTALL NO. 4 AIR DUCT SUB-ASSEMBLY

Engage the 3 claws to install a new No. 4 air duct sub-assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the bolt.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf)

INSTALL FRONT NO. 1 CONSOLE BOX INSERT
Refer to PROCEDURE - Step 4 [08/2019 - ]
INSTALL CONSOLE BOX ASSEMBLY
Refer to PROCEDURE - Step 1 [08/2019 - ]
INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 2 [08/2019 - ]
INSTALL CONSOLE PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 4 [08/2019 - ]
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Refer to PROCEDURE - Step 6 [08/2019 - ]
INSTALL REAR CONSOLE UPPER PANEL
Refer to PROCEDURE - Step 9 [08/2019 - ]
INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Refer to INSTALLATION [03/2018 - ]

INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTE:

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this direction

Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

INSTALL UPPER STEERING COLUMN COVER

Engage the 6 clips to the upper steering column cover.

Engage the 2 claws to install the upper steering column cover.

Install in this direction

INSTALL LOWER STEERING COLUMN COVER

Engage the 2 claws to install the lower steering column cover.

Install the 3 screws.

Torque: 2.0 N*m (20 kgf*cm, 18 in.*lbf)

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Refer to PROCEDURE - Step 7 [08/2016 - ]
INSTALL STEERING WHEEL ASSEMBLY
See step [08/2019 - 07/2020], or see step [07/2020 - ]
CHECK STEERING WHEEL CENTER POINT
INSTALL HORN BUTTON ASSEMBLY
Refer to INSTALLATION [03/2018 - ]
CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
1. Set the auto tilt away function setting to the previous condition by changing the customize parameter.
  Refer to CUSTOMIZE PARAMETERS [10/2015 - ]
PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
Refer to CALIBRATION [10/2015 - ]
ADJUST PARKING ASSIST MONITOR SYSTEM
Refer to CALIBRATION [08/2019 - ]
ADJUST PANORAMIC VIEW MONITOR SYSTEM (w/ Panoramic View Monitor System)
Refer to CALIBRATION [08/2019 - ]
ADJUST INTELLIGENT CLEARANCE SONAR SYSTEM (w/ Intelligent Clearance Sonar System)
Refer to CALIBRATION [08/2019 - ]