Driver Side Power Window does not Operate with Power Window Master Switch [08/2019 - ]: Procedure
- CHECK FOR DTC (B2312)
- Check if DTC B2312 is output (Refer to DTC B2312: Power Window Switch Malfunction [08/2015 - ] ).
OK
DTC B2312 is not output.
Result:
NG
GO TO DTC B2312
(Refer to DTC B2312: Power Window Switch Malfunction [08/2015 - ] )
Result:
OK
See step 2
- Check if DTC B2312 is output (Refer to DTC B2312: Power Window Switch Malfunction [08/2015 - ] ).
- READ VALUE USING TECHSTREAM (MULTIPLEX NETWORK MASTER SWITCH)
- Use the Data List to check if the multiplex network master switch is functioning properly (Refer to DATA LIST / ACTIVE TEST [08/2015 - ]
).D-DOOR MOTOR
Tester Display Measurement Item/Range Normal Condition Diagnostic Note D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated- D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated- OK
On tester screen, each item changes between ON and OFF according to above chart.
Result:
NG
See step 4
Result:
OK
See step 3
- Use the Data List to check if the multiplex network master switch is functioning properly (Refer to DATA LIST / ACTIVE TEST [08/2015 - ]
).
- PERFORM ACTIVE TEST USING TECHSTREAM (POWER WINDOW)
- Select the Active Test, use the Techstream to generate a control command, and then check that power window regulator motor operates (Refer to DATA LIST / ACTIVE TEST [08/2015 - ]
).D-DOOR MOTOR
Tester Display Test Part Control Range Diagnostic Note Power Window Driver side power window OFF/UP/DOWN - OK
The power window regulator motor operates normally.
Result:
OK
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(Refer to DATA LIST / ACTIVE TEST [08/2015 - ] )
Result:
NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
(Refer to REMOVAL [08/2015 - ] )
- Select the Active Test, use the Techstream to generate a control command, and then check that power window regulator motor operates (Refer to DATA LIST / ACTIVE TEST [08/2015 - ]
).
- CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
- Disconnect the K3 multiplex network master switch connector.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition K3-11 (B) - Body ground Always 11 to 14 V - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition K3-12 (GND) - Body ground Always Below 1 Ω TEXT IN ILLUSTRATION*a Front view of wire harness connector
(to Multiplex Network Master Switch Assembly)
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 5
- Disconnect the K3 multiplex network master switch connector.
- CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
- Disconnect the K6 power window regulator motor connector.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition K6-2 (B) - Body ground Always 11 to 14 V - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition K6-1 (GND) - Body ground Always Below 1 Ω TEXT IN ILLUSTRATION*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 6
- Disconnect the K6 power window regulator motor connector.
- CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
- Disconnect the K3 multiplex network master switch connector.
- Disconnect the K6 power window regulator motor connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition K3-20 (UP) - K6-10 (UP) Always Below 1 Ω K3-15 (DOWN) - K6-7 (DOWN) Always Below 1 Ω K3-20 (UP) - Body ground Always 10 kΩ or higher K3-15 (DOWN) - Body ground Always 10 kΩ or higher
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 7
- INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
- Remove the front power window regulator motor assembly LH.
Refer to REMOVAL [08/2015 - ]
- Inspect the front power window regulator motor assembly LH.
Refer to INSPECTION [08/2015 - ]
Result:
OK
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
(Refer to REMOVAL [08/2015 - ] )
Result:
NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
(Refer to REMOVAL [08/2015 - ] )
- Remove the front power window regulator motor assembly LH.