Data List / Active Test [09/2014 - 11/2017]
- DATA LIST NOTE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / ASC / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > ASC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Sound State Dynamic engine sound output status Stopping or Sounding Stopping: Dynamic engine sound stopped
Sounding: Dynamic engine sound being output- Mute Mute setting OFF or ON OFF: Mute off
ON: Mute on- Gear Position (D Range) Gear position information 1st, 2nd, 3rd, 4th, 5th, 6th, 7th*1 or 8th*1 Actual gear position - Suppositional Engine Speed (Target Value) Calculated engine speed in the stereo component equalizer assembly Min.: 0 rpm
Max.: 8000 rpmChanges according to driving conditions (accelerator pedal opening angle, vehicle speed, etc.) - Volume SW Vehicle sound switch on/off status OFF or ON OFF: Vehicle sound switch off
ON: Vehicle sound switch on- Speaker Disconnection Inspection State of wire harness between stereo component equalizer assembly and No. 1 speaker assembly with box OFF or Inspecting OFF: Open not detected
Inspecting: Open detected- Volume Switch Voltage The VSLI terminal voltage to the CPU of the stereo component equalizer assembly Min.: 0 V
Max.: 5 VChanges according to vehicle sound switch volume setting - Pseudo Engine Revolution (HV ECU) Actual engine speed Min.: 0 rpm
Max.: 12800 rpmActual engine speed *2 Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h
Max.: 655.35 km/hActual vehicle speed - Accelerator Position Accelerator pedal opening angle Min.: 0 %
Max.: 111.0 %Actual accelerator pedal opening angle - Shift SW Status (P Range) Park/Neutral position switch status OFF or ON OFF: Shift lever in any position other than P
ON: Shift lever in P- Shift SW Status (R Range) Shift lever position (R) OFF or ON OFF: Shift lever in any position other than R
ON: Shift lever in R- Shift SW Status (D Range) Shift lever position (D) OFF or ON OFF: Shift lever in any position other than D
ON: Shift lever in D- Shift SW Status (N Range) Shift lever position (N) OFF or ON OFF: Shift lever in any position other than N
ON: Shift lever in N- Gear Position (Sports Mode) Gear position information with shift lever in M Not Sports Mode, 1st, 2nd, 3rd, 4th, 5th, 6th, 7th*1 or 8th*1 Not Sports Mode: Shift lever in any position other than M
1st: 1st gear selected
2nd: 2nd gear selected
3rd: 3rd gear selected
4th: 4th gear selected
5th: 5th gear selected
6th: 6th gear selected
7th: 7th gear selected*1
8th: 8th gear selected*1- Current Gear Position (D Range) Current gear position information 1st, 2nd, 3rd, 4th, 5th, 6th, 7th*1 or 8th*1 Current gear position displayed (1st, 2nd, 3rd, 4th, 5th, 6th, 7th*1 or 8th*1) - Integrated Sport Mode Indicator Drive mode (SPORT) status OFF or Lighting OFF: Drive mode other than SPORT mode selected
Lighting: SPORT mode selected- Sport Mode Indicator M position switch status OFF or Lighting OFF: Shift lever in any position other than M
Lighting: Shift lever in M- SNOW Mode Indicator SNOW mode indicator illumination status OFF or Lighting OFF: SNOW mode indicator not illuminated
Lighting: SNOW mode indicator illuminated- ECO Mode Indicator ECO mode indicator illumination status OFF or Lighting OFF: ECO mode indicator not illuminated
Lighting: ECO mode indicator illuminated- Engine Mode Engine operating status Stopped, Move to Stopping, Starting or Running Stopped: Engine stopped
Move to Stopping: Engine attempting to stop
Starting: Engine attempting to start
Running: Engine running*2 EV Mode EV mode indicator illumination status OFF or Lighting OFF: EV mode indicator not illuminated
Lighting: EV mode indicator illuminated*2 Integrated Sport Mode Status Drive mode (SPORT S or SPORT S+) status Not Sport, PWR & Chassis, Chassis or PWR Not Sport: Drive mode other than SPORT S or SPORT S+ mode selected
PWR & Chassis: SPORT S+ mode selected
PWR: SPORT S mode selected- Engine Revolution Actual engine speed Min.: 0 rpm
Max.: 1280 rpmActual engine speed - Gear Shifting Signal Shifting status OFF or ON OFF: Gear not being changed
ON: Gear being changed- Number of DTC Number of trouble codes Min.: 0
Max.: 255Number of DTCs displayed - HINT:
*1: for AA81E automatic transmission
*2: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / ASC / Active Test.
- Perform the Active Test according to the display on the Techstream.
Body Electrical > ASC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Sound ASC system ON or OFF -