How To Proceed With Troubleshooting [09/2022 - ]: Procedure

Result

Result: 

NEXT 

See step  2

Result

Result: 

NEXT 

See step  3

1. Measure the auxiliary battery voltage with the ignition switch off.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Use the GTS to check if the CAN communication system is functioning normally.

   for Gasoline Model: Refer to DIAGNOSIS SYSTEM [09/2022 - ]

   for HV Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]

   Result

   Result	Proceed to
   CAN communication system DTCs are not output	A
   CAN communication system DTCs are output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM 

for Gasoline Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]

for HV Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]

Result: 

A 

See step  5

1. Check the vehicle specifications.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  6

1. Use the GTS to check if the blind spot monitor system is functioning normally.

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO BLIND SPOT MONITOR SYSTEM 

for Gasoline Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]

for HV Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]

Result: 

A 

See step  7

1. Choose the model to be inspected.

   Result

   Result	Proceed to
   w/ Panoramic View Monitor System	A
   w/ Parking Assist Monitor System	B

Result: 

B 

See step  20

Result: 

A 

See step  8

1. Use the GTS to check if the panoramic view monitor system is functioning normally.

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO PANORAMIC VIEW MONITOR SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - ] 

Result: 

A 

See step  9

Result

Result: 

NEXT 

See step  10

1. Check for DTCs and note any codes that are output.

   Body Electrical > Clearance Warning > Trouble Codes 

2. Clear the DTCs.

   Body Electrical > Clearance Warning > Clear DTCs 

3. Check for DTCs.

   Body Electrical > Clearance Warning > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are output	A
   DTCs are not output	B

Result: 

B 

See step  12

Result: 

A 

See step  11

1. Refer to Diagnostic Trouble Code Chart.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [09/2022 - ] 

   NOTE:

   The clearance warning ECU assembly outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the parking support alert system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

   System	Proceed to
   Parking Support Brake System	Refer to DIAGNOSTIC TROUBLE CODE CHART [09/2022 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  16

HINT: 

Refer to Vehicle Control History.

Refer to VEHICLE CONTROL HISTORY (RoB) [09/2022 - ]

1. Check for vehicle control history and note any codes that are output.

   Body Electrical > Clearance Warning > Utility 

   Tester Display
   Vehicle Control History (RoB)

   Result

   Result	Proceed to
   No vehicle control history is output (Problem symptom does not occur)	A
   No vehicle control history is output (Problem symptom occurs)	B
   X20C0 or X20C1 is output	C
   Any vehicle control history other than X20C0 and X20C1 is output	D

Result: 

B 

See step  14

Result: 

C 

GO TO CALIBRATION. Refer to  CALIBRATION [09/2022 - ] 

Result: 

D 

GO TO VEHICLE CONTROL HISTORY. Refer to  VEHICLE CONTROL HISTORY (RoB) [09/2022 - ] 

Result: 

A 

See step  13

1. Refer to Symptom Simulation.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  14

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [09/2022 - ] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table	A
   Fault is listed in Problem Symptoms Table	B

Result: 

B 

See step  16

Result: 

A 

See step  15

1. Terminals of ECU

   Refer to TERMINALS OF ECU [09/2022 - ] 

2. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [09/2022 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  16

Result

Result: 

NEXT 

See step  17

Result

Result: 

NEXT 

See step  18

Result

Result: 

NEXT 

See step  19

Result

Result: 

NEXT 

END 

1. Use the GTS to check if the parking assist monitor system is functioning normally.

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

A 

See step  9

Result: 

B 

GO TO PARKING ASSIST MONITOR SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - ]