How To Proceed With Troubleshooting [10/2023 - ]: Procedure

Result

Result: 

NEXT 

See step  2

HINT: 

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.

Result

Result: 

NEXT 

See step  3

1. Measure the battery voltage with the ignition switch off.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Use the GTS to check if the CAN communication system is functioning normally.

   Refer to DIAGNOSIS SYSTEM [10/2023 - ]

   Result

   Result	Proceed to
   CAN communication system DTCs are not output	A
   CAN communication system DTCs are output (for Gasoline Model)	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2023 - ] 

Result: 

A 

See step  5

1. Refer to DTC Check / Clear for the blind spot monitor system.

   Body Electrical > Blind Spot Monitor "B" > Trouble Codes 

   Body Electrical > Blind Spot Monitor "A" > Trouble Codes 

2. Record or print DTCs and freeze frame data, if necessary.

   Refer to FREEZE FRAME DATA [10/2023 - ] 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2023 - ]  

Result: 

A 

See step  6

1. Check for vehicle control history and note any codes that are output.

   Body Electrical > Blind Spot Monitor "B" > Utility 

   Tester Display
   Vehicle Control History (RoB)

   Body Electrical > Blind Spot Monitor "A" > Utility 

   Tester Display
   Vehicle Control History (RoB)

   NOTE:

   Record or print Vehicle control history (RoB), if necessary.

   Result

   Result	Proceed to
   Vehicle control history (RoB) is output	A
   Vehicle control history (RoB) is not output	B

Result: 

B 

GO TO VEHICLE CONTROL HISTORY (RoB). Refer to  VEHICLE CONTROL HISTORY (RoB) [10/2023 - ] 

Result: 

A 

See step  7

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [10/2023 - ] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table	A
   Fault is listed in Problem Symptoms Table	B

   HINT: 

   If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Result: 

B 

GO TO PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [10/2023 - ]  

Result: 

A 

See step  8

1. Refer to Terminals of ECU.

   Refer to TERMINALS OF ECU [10/2023 - ] 

2. Refer to Diagnosis System.

   Refer to DIAGNOSIS SYSTEM [10/2023 - ] 

3. Refer to Data List / Active Test.

   Refer to DATA LIST / ACTIVE TEST [10/2023 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

Result

Result: 

B 

See step  11

Result: 

A 

See step  10

1. Clear the DTCs.

   Body Electrical > Blind Spot Monitor "B" > Clear DTCs 

   Body Electrical > Blind Spot Monitor "A" > Clear DTCs 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  11

1. Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

   Driving Adjustment: Refer to DRIVING ADJUSTMENT [10/2023 - ]

   Target Adjustment (Triangle Target) : Refer to TARGET ADJUSTMENT(TRIANGLE TARGET) [10/2023 - ]

   ECU data Save / Write: Refer to ECU DATA SAVE/WRITE [10/2023 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  12

Result

Result: 

NEXT 

END