LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2021 >> LX 570 >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Multi-Terrain Monitor System (Diagnostics - Introduction) >> Multi-Terrain Monitor System >> How To Proceed With Troubleshooting [09/2015 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

How To Proceed With Troubleshooting [09/2015 - ]: Procedure

  1. VEHICLE BROUGHT TO WORKSHOP 

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  2

  2. INSPECT BATTERY VOLTAGE 
    1. Measure the battery voltage with the engine switch off.

      Standard Voltage

      11 to 14 V

      If the voltage is below 11 V, replace or recharge the battery before proceeding.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  3

  3. CHECK NAVIGATION SYSTEM 
    1. Refer to the navigation system.

      Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - ]

      Result

      Result Proceed to
      Navigation system is normal A
      Navigation system is abnormal B

    Result: 

    GO TO NAVIGATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - ] 

    Result: 

    See step  4

  4. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* 
    1. Use the Techstream to check if the CAN communication system is functioning normally.

      Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - 08/2020] Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2020 - ]

      Result

      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output B

    Result: 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2015 - 08/2020]  Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2020 - ] 

    Result: 

    See step  5

  5. CHECK FOR DTC* 
    1. Check for DTCs and note any codes that are output.

      Refer to DTC CHECK / CLEAR [09/2015 - ] 

    2. Clear the DTC.

      Refer to DTC CHECK / CLEAR [09/2015 - ] 

    3. Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

      Result

      Result Proceed to
      DTC is not output A
      DTC is output B

    Result: 

    GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2015 - ]  

    Result: 

    See step  6

  6. PROBLEM SYMPTOMS TABLE 
    1. Refer to the Problem Symptoms Table.

      Refer to PROBLEM SYMPTOMS TABLE [09/2015 - ] 

      Result

      Result Proceed to
      Fault is not listed in Problem Symptoms Table A
      Fault is listed in Problem Symptoms Table B

    Result: 

    ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE 

    Result: 

    See step  7

  7. OVERALL ANALYSIS AND TROUBLESHOOTING* 
    1. Data List / Active Test.

      Refer to DATA LIST / ACTIVE TEST [09/2015 - ] 

    2. Terminals of ECU.

      Refer to TERMINALS OF ECU [09/2015 - ] 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  8

  8. ADJUST, REPAIR OR REPLACE 

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  9

  9. CONFIRMATION TEST 

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    END