Back Door Entry Unlock Function does not Operate [01/2019 - ]: Procedure

1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

   Refer to OPERATION CHECK [10/2014 - ]

   OK

   Door locks operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO POWER DOOR LOCK CONTROL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] 

Result: 

OK 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Access / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Smart Access > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   B-Dr Opening Operation	Back door opening operation	Long, Twice or OFF	Customize setting displayed	-

   Body Electrical > Smart Access > Data List 

   Tester Display
   B-Dr Opening Operation

   Result

   Result	Proceed to
   Customize setting is Long or Twice	A
   Customize setting is OFF	B

Result: 

B 

PERFORM CUSTOMIZE SETTING (Proceed to Customize Parameters). Refer to  CUSTOMIZE PARAMETERS [09/2017 - ] 

Result: 

A 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Access / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Smart Access > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Tr/B-Door Unlock SW	Back door opener switch assembly (open switch)	ON or OFF	ON: Back door opener switch assembly (open switch) pressed OFF: Back door opener switch assembly (open switch) not pressed	Displays whether the back door opener switch assembly (open switch) is on or off. Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.

   Body Electrical > Smart Access > Data List 

   Tester Display
   Tr/B-Door Unlock SW

   OK

   The Techstream display changes correctly in response to the operation of the back door opener switch assembly.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [10/2014 - ] 

Result: 

NG 

See step  4

1. Disconnect the Y30 back door opener switch assembly connector.
2. Disconnect the I52 certification ECU (smart key ECU assembly) connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Y30-1 (UL) - I52-5 (TSW5)	Always	Below 1 Ω
   Y30-1 (UL) or I52-5 (TSW5) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  5

1. Remove the back door opener switch assembly.

   Refer to REMOVAL [10/2014 - ]

2. Inspect the back door opener switch assembly.

   Refer to INSPECTION [01/2019 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY). Refer to  REMOVAL [10/2014 - ] 

Result: 

NG 

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY. Refer to  REMOVAL [10/2014 - ]