DTC C1299: Cancellation of 4WD Control [05/2019 - ]: Procedure

1. Check that there has been no unintended vehicle usage.

   OK

   There is no evidence of rough use (the vehicle has not been driven on damaged or snowy roads, etc. for a long time).

   Result

   Proceed to
   OK
   NG

Result: 

NG 

CHECK FOR INTERMITTENT PROBLEMS. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - 10/2019]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2019 - 07/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2020 - ] 

Result: 

OK 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Check if the brake control system DTC is output.

   Refer to DTC CHECK / CLEAR [05/2019 - ]

   Chassis > ABS/VSC/TRAC > Trouble Codes 

5. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   Only DTC C1299 is output	A
   DTC C1299 and other DTCs (brake control system DTC)	B

Result: 

B 

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [05/2019 - ] 

Result: 

A 

See step  3

1. Check the condition, size and tire pressure of the front and rear tires.
2. Inspect the suspension and ball joint, etc. for rattle.
3. Inspect the drive shaft and propeller shaft rotation condition.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE MALFUNCTIONING PARTS 

Result: 

OK 

See step  4

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [05/2019 - ]

   Chassis > Four Wheel Drive > Clear DTCs 

2. Start the engine.
3. Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

   Refer to DTC CHECK / CLEAR [05/2019 - ]

   Chassis > Four Wheel Drive > Trouble Codes 

   Result

   Proceed to
   DTC is output
   DTC is not output

Result: 

DTC is not output 

CHECK FOR INTERMITTENT PROBLEMS. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - 10/2019]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2019 - 07/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2020 - ] 

Result: 

DTC is output 

See step  5

1. Replace the 4WD ECU assembly.

   Refer to REMOVAL [05/2019 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  6

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [05/2019 - ]

   Chassis > Four Wheel Drive > Clear DTCs 

2. Start the engine.
3. Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

   Refer to DTC CHECK / CLEAR [05/2019 - ]

   Chassis > Four Wheel Drive > Trouble Codes 

   Result

   Proceed to
   DTC is output
   DTC is not output

Result: 

DTC is output 

REPLACE TRANSMISSION COUPLING ASSEMBLY. Refer to  REMOVAL [10/2014 - ] 

Result: 

DTC is not output 

END