LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2022 >> LC 500h >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System - Diagnostic Codes & Symptom Tests >> Power Window Control System >> Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [01/2017 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [01/2017 - ]: Procedure

  1. READ VALUE USING TECHSTREAM (P-DOOR MOTOR) 
    1. Read the Data List according to the display on the Techstream.

      Refer to DATA LIST / ACTIVE TEST [01/2017 - ]

      Body Electrical > P-Door Motor > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated
      ON: Front passenger door power window manual up switch being operated      		 -
      P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated
      ON: Front passenger door power window manual down switch being operated      		 -

      Body Electrical > P-Door Motor > Data List 

      Tester Display
      P Door P/W Up SW
      P Door P/W Down SW

      OK

      On the Techstream screen, ON or OFF is displayed accordingly.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [01/2017 - 05/2023]  , or refer to  REMOVAL [05/2023 - ] 

    Result: 

    NG 

    See step  2

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY 
    1. Remove the power window regulator switch assembly.

      Refer to REMOVAL [01/2017 - ]

    2. Inspect the power window regulator switch assembly.

      Refer to INSPECTION [01/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY. Refer to  REMOVAL [01/2017 - ] 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - AUXILIARY BATTERY AND BODY GROUND) 
    1. Disconnect the front multiplex network door ECU RH connector.
      GTY776552Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Front Multiplex Network Door ECU RH)
    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      R9-6 (BDR) - R9-1 (GND) Power switch off 11 to 14 V
      R9-3 (SIG) - R9-1 (GND) Power switch on (IG) 11 to 14 V

      Standard Resistance

      Tester Connection Condition Specified Condition
      R9-1 (GND) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - FRONT MULTIPLEX NETWORK DOOR ECU RH) 
    1. Disconnect the R2 power window regulator motor assembly RH connector.
    2. Disconnect the R9 front multiplex network door ECU RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      R2-2 (B) - R9-5 (BDRJ) Always Below 1 Ω
      R2-1 (GND) - R9-2 (PWE) Always Below 1 Ω
      R2-2 (B) or R9-5 (BDRJ) - Body ground Always 10 kΩ or higher
      R2-1 (GND) or R9-2 (PWE) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH 
    1. Measure the voltage according to the value(s) in the table below.
      GTY833428Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Front Multiplex Network Door ECU RH)      		 - -

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      R9-5 (BDRJ) - Body ground Power switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH. Refer to  DISASSEMBLY [01/2017 - 06/2019]  , or refer to  DISASSEMBLY [06/2019 - 04/2020]  , or refer to  DISASSEMBLY [04/2020 - 05/2023]  , or refer to  DISASSEMBLY [05/2023 - ] 

    Result: 

    OK 

    See step  6

  6. INSPECT FRONT MULTIPLEX NETWORK DOOR ECU RH 
    1. Remove the front multiplex network door ECU RH.

      Refer to DISASSEMBLY [01/2017 - 06/2019] , or refer to DISASSEMBLY [06/2019 - 04/2020] , or refer to DISASSEMBLY [04/2020 - 05/2023] , or refer to DISASSEMBLY [05/2023 - ]

      GTY651087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Front Multiplex Network Door ECU RH)      		 - -
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (PWE) - 1 (GND) Always Below 1 Ω
      9 (SGND) - 1 (GND) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH. Refer to  DISASSEMBLY [01/2017 - 06/2019]  , or refer to  DISASSEMBLY [06/2019 - 04/2020]  , or refer to  DISASSEMBLY [04/2020 - 05/2023]  , or refer to  DISASSEMBLY [05/2023 - ] 

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU RH) 
    1. Disconnect the T1 power window regulator switch assembly connector.
    2. Disconnect the R9 front multiplex network door ECU RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T1-5 (GND) - R9-9 (SGND) Always Below 1 Ω
      T1-5 (GND) or R9-9 (SGND) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) 
    1. Disconnect the T1 power window regulator switch assembly connector.
    2. Disconnect the R2 power window regulator motor assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T1-2 (UP) - R2-10 (UP) Always Below 1 Ω
      T1-10 (DOWN) - R2-7 (DOWN) Always Below 1 Ω
      T1-4(AUTO) - R2-4(AUTO) Always Below 1 Ω
      T1-2 (UP) or R2-10 (UP) - Body ground Always 10 kΩ or higher
      T1-10 (DOWN) or R2-7 (DOWN) - Body ground Always 10 kΩ or higher
      T1-4(AUTO) or R2-4(AUTO) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH. Refer to  REMOVAL [01/2017 - 05/2023]  , or refer to  REMOVAL [05/2023 - ] 

    Result: 

    NG 

    See step  10

  9. INSPECT FRONT DOOR WIRE RH 
    1. Turn the power switch off.
      GTY831457Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Door Wire RH - -
      *a Front view of wire harness connector
      (to Vehicle Side Connector)      		 *b Front view of wire harness connector
      (to Power Window Regulator Switch Assembly Side Connector)
    2. Disconnect the T1 front door wire RH connector.
    3. Disconnect the TR1 front door wire RH connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T1-5 (GND) - TR1-4 Always Below 1 Ω
      T1-5 (GND) or TR1-4 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT DOOR WIRE RH. Refer to  DISASSEMBLY [01/2017 - 06/2019]  , or refer to  DISASSEMBLY [06/2019 - 04/2020]  , or refer to  DISASSEMBLY [04/2020 - 05/2023]  , or refer to  DISASSEMBLY [05/2023 - ] 

  10. INSPECT FRONT DOOR WIRE RH 
    1. Turn the power switch off.
      GTY794232Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Door Wire RH - -
      *a Front view of wire harness connector
      (to Vehicle Side Connector)      		 *b Front view of wire harness connector
      (to Power Window Regulator Switch Assembly Side Connector)
    2. Disconnect the T1 front door wire RH connector.
    3. Disconnect the TR1 front door wire RH connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T1-2 (UP) - TR1-5 Always Below 1 Ω
      T1-10 (DOWN) - TR1-13 Always Below 1 Ω
      T1-4 (AUTO) - TR1-6 Always Below 1 Ω
      T1-2 (UP) or TR1-5 - Body ground Always 10 kΩ or higher
      T1-10 (DOWN) or TR1-13 - Body ground Always 10 kΩ or higher
      T1-4 (AUTO) or TR1-6 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT DOOR WIRE RH. Refer to  DISASSEMBLY [01/2017 - 06/2019]  , or refer to  DISASSEMBLY [06/2019 - 04/2020]  , or refer to  DISASSEMBLY [04/2020 - 05/2023]  , or refer to  DISASSEMBLY [05/2023 - ] 

scientia non olet · About LEMON Manuals