October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.
On-Vehicle Inspection [01/2017 - ]: Procedure
- INSPECT NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI MAIN NO. 1)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
| Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSPECT NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI MAIN NO. 2)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
| Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSPECT ELECTRONIC DRIVER UNIT RELAY (EDU RELAY)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
| Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F HTR RELAY)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
| Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSPECT NO. 1 IGNITION RELAY (IG1)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
| Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSPECT NO. 2 IGNITION RELAY (IG2 NO. 2)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
| Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (IG2 D RELAY)
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
| *a |
Component without harness connected
(Driver Side Junction Block Assembly) |
- |
- |
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
| Tester Connection |
Condition |
Specified Condition |
| 3E-1 - 3B-26 |
Battery voltage not applied between terminals 3B-18 and 3B-6 |
10 kΩ or higher |
| Battery voltage applied between terminals 3B-18 and 3B-6 |
Below 1 Ω |