| B103C:01 |
Left Headlamp Control: General Electrical Failure |
INSTALL a new headlamp assembly. Headlamp Assembly - Navigator
. |
| B103C:13 |
Left Headlamp Control: Circuit Open |
INSTALL a new headlamp assembly. Headlamp Assembly - Navigator
. |
| B103D:01 |
Right Headlamp Control: General Electrical Failure |
INSTALL a new headlamp assembly. Headlamp Assembly - Navigator
. |
| B103D:13 |
Right Headlamp Control: Circuit Open |
INSTALL a new headlamp assembly. Headlamp Assembly - Navigator
. |
| B1D64:01 |
Left Headlamp Swiveling Motor: General Electrical Failure |
GO to Pinpoint Test X |
| B1D64:64 |
Left Headlamp Swiveling Motor: Signal Plausibility Failure |
GO to Pinpoint Test X |
| B1D65:01 |
Right Headlamp Swiveling Motor: General Electrical Failure |
GO to Pinpoint Test X |
| B1D65:64 |
Right Headlamp Swiveling Motor: Signal Plausibility Failure |
GO to Pinpoint Test X |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test T |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test U |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
RETRIEVE and REPAIR all non-network DTCs from the PCM. REFER to
Electronic Engine Controls
. If there are no DTCs present in the PCM, DIAGNOSE the observable symptom. |
| U0415:00 |
Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
RETRIEVE and REPAIR all non-network DTCs from the ABS module. REFER to
Anti-Lock Brake System (ABS) and Stability
. If there are no DTCs present in the ABS module, DIAGNOSE the observable symptom. |
| U0416:00 |
Invalid Data Received From Vehicle Dynamics Control Module: No Sub Type Information |
RETRIEVE and REPAIR all non-network DTCs from the VDM. REFER to
Vehicle Dynamic Suspension
. If there are no DTCs present in the VDM, DIAGNOSE the observable symptom. |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
RETRIEVE and REPAIR all non-network DTCs from the BCM. REFER to
Multifunction Electronic Modules
. If there are no DTCs present in the BCM, DIAGNOSE the observable symptom. |
| U0429:00 |
Invalid Data Received From Steering Column Control Module: No Sub Type Information |
RETRIEVE and REPAIR all non-network DTCs from the SCCM. REFER to
Steering Column Switches
. If there are no DTCs present in the SCCM, DIAGNOSE the observable symptom. |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
RETRIEVE and REPAIR all non-network DTCs from the RCM. REFER to
Supplemental Restraint System
. If there are no DTCs present in the RCM, DIAGNOSE the observable symptom. |
| U1000:00 |
Solid State Driver Protection Active - Driver Disabled: No Sub Type Information |
GO to Pinpoint Test S |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to
Module Configuration
. If there have been no recent service actions, INSTALL a new HCM. REFER to Headlamp Control Module (HCM)
. |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to
Module Configuration
. If there have been no recent service actions, INSTALL a new HCM. REFER to Headlamp Control Module (HCM)
. |
| U3000:45 |
Control Module: Program Memory Failure |
CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new HCM. REFER to Headlamp Control Module (HCM)
. |
| U3000:46 |
Control Module: Calibration/Parameter Memory Failure |
CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new HCM. REFER to Headlamp Control Module (HCM)
. |
| U3000:49 |
Control Module: Internal Electronic Failure |
DIAGNOSE all other DTCs first. After the repair, INSTALL a new HCM. REFER to Headlamp Control Module (HCM)
. |