Common Specifications & Procedures
MKC COMMON SPECIFICATIONS & PROCEDURES
| System | Specifications/Procedures | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | Refer to appropriate component in REMOVAL AND INSTALLATION . | ||
| Axle Nut/Hub Nut | |||
| AWD | |||
| Hub Bolt | 81 lb.ft (110 Nm) | ||
| Spindle Nut | 98 lb.ft (133 Nm) | ||
| FWD | 81 lb.ft (110 Nm) | ||
| Battery | SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM PRESSURE BLEEDING | ||
| Front Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION . | ||
| Rear Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION . | ||
| Charging | |||
| Generator w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION . | ||
| Drive Belts | |||
| Adjustment | |||
| 2.0L Ecoboost | ACCESSORY DRIVE | ||
| 2.3L Ecoboost | ACCESSORY DRIVE | ||
| Belt Routing | |||
| 2.0L Ecoboost | ACCESSORY DRIVE - COMPONENT LOCATION | ||
| 2.3L Ecoboost | ACCESSORY DRIVE - COMPONENT LOCATION | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.0L Ecoboost | SPECIFICATIONS | ||
| 2.3L Ecoboost | SPECIFICATIONS | ||
| Radiator Cap Pressure | 120 kPa (17.4 psi) to 150 kPa (21.7 psi) | ||
| Thermostat R & I | |||
| 2.0L Ecoboost | THERMOSTAT HOUSING | ||
| 2.3L Ecoboost | THERMOSTAT HOUSING | ||
| Water Pump R & I | |||
| 2.0L Ecoboost | COOLANT PUMP | ||
| 2.3L Ecoboost | COOLANT PUMP | ||
| Engine Mechanical | |||
| 2.0L Ecoboost | |||
| Compression | SPECIFICATIONS | ||
| Oil pressure (hot @ 2, 000 rpm) | 29-60 psi (200-414 kPa) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to appropriate component in REMOVAL AND INSTALLATION . | ||
| 2.3L Ecoboost | |||
| Compression | SPECIFICATIONS | ||
| Oil pressure (hot @ 2, 000 rpm) | 29-60 psi (200-414 kPa) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to appropriate component in REMOVAL AND INSTALLATION | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 2.0L Ecoboost | For tightening sequence, refer to FLEXPLATE Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
||
| 2.3L Ecoboost | For tightening sequence, refer to FLEXPLATE Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
||
| Fuel System | |||
| Fuel Filter Location | Located in fuel tank as part of Fuel Pump Module. | ||
| Fuel Filter R & I | |||
| 2.0L Ecoboost | FUEL PUMP AND SENDER UNIT | ||
| 2.3L Ecoboost | FUEL PUMP AND SENDER UNIT | ||
| Pressure Release Procedure | |||
| 2.0L Ecoboost | FUEL SYSTEM PRESSURE RELEASE | ||
| 2.3L Ecoboost | FUEL SYSTEM PRESSURE RELEASE | ||
| Pressure Specification | |||
| 2.0L Ecoboost | SPECIFICATIONS | ||
| 2.3L Ecoboost | SPECIFICATIONS | ||
| Fuel Pressure Test Procedure | |||
| 2.0L Ecoboost | FUEL SYSTEM PRESSURE CHECK | ||
| 2.3L Ecoboost | FUEL SYSTEM PRESSURE CHECK | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-3-4-2 FIRING ORDER & CYLINDER IDENTIFICATION |
||
| Ignition Wires (Routing) | Engines are equipped with Coil-on-plug ignition. | ||
| Spark Plugs | |||
| 2.0L Ecoboost | |||
| Type | CYFS 12Y PCT | ||
| Gap | 0.031 in (.8 mm) | ||
| Torque | 106 lb.in (12 Nm) | ||
| 2.3L Ecoboost | |||
| Type | CYFS 12Y PCT | ||
| Gap | 0.031 in (.8 mm) | ||
| Torque | 133 lb.in (15 Nm) | ||
| Starting | |||
| Starter | |||
| 2.0L Ecoboost | SPECIFICATIONS | ||
| 2.3L Ecoboost | SPECIFICATIONS | ||
| Torque | Refer to appropriate component in REMOVAL AND INSTALLATION - 2.0 EcoBoost or REMOVAL AND INSTALLATION - 2.3 EcoBoost. | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS | ||
| Torque | Refer to the appropriate component in ALIGNMENT SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | For tightening sequence, refer to WHEEL AND TIRE
. 100 Ft. Lbs. (135 N.m) |
||