Occupant Classification System Module (OCSM)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short To Ground | REFER to: Pinpoint Test - DTC: AP |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short To Battery | REFER to: Pinpoint Test - DTC: AP |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | REFER to: Pinpoint Test - DTC: AP |
| B0061:64 | Passenger Seatbelt Tension Sensor: Signal Plausibility Failure | REFER to: Pinpoint Test - DTC: AP |
| B00A0:62 | Occupant Classification System: Signal Component Failure | REFER to: Pinpoint Test - DTC: AS |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short to Ground | INSPECT the OCS for any damage and for correct installation. If damage is found, REPAIR the root cause of the damage and INSTALL a new OCS, as necessary. REFER to: Occupant Classification System (OCS) Sensor If any installation concerns are found, CORRECT the OCS installation, referring to the OCS Removal and Installation procedure as needed to make sure the sensor hose is free from kinks and correctly routed. REFER to: Occupant Classification System (OCS) Sensor If no damage or installation concerns are found, INSTALL a new OCS. REFER to: Occupant Classification System (OCS) Sensor |
| B00C0:12 | Passenger Seat Occupant Classification Sensor "A": Circuit Short to Battery | INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| B00C0:16 | Passenger Seat Occupant Classification Sensor "A": Circuit Voltage Below Threshold | INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| B00C0:7B | Passenger Seat Occupant Classification Sensor "A": Low Fluid Level | INSPECT the OCS for any damage and for correct installation. If damage is found, REPAIR the root cause of the damage and INSTALL a new OCS, as necessary. REFER to: Occupant Classification System (OCS) Sensor If any installation concerns are found, CORRECT the OCS installation, referring to the OCS Removal and Installation procedure as needed to make sure the sensor hose is free from kinks and correctly routed. REFER to: Occupant Classification System (OCS) Sensor If no damage or installation concerns are found, INSTALL a new OCS. REFER to: Occupant Classification System (OCS) Sensor |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | REFER to: Pinpoint Test - DTC: AQ |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | REFER to: Pinpoint Test - DTC: AQ |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | CLEAR the OCSM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC B1193:00 returns, INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| U0100:00 | Lost Communication with ECM/PCM A: No Sub Type Information | REFER to: Pinpoint Test - DTC: AI |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | REFER to: Pinpoint Test - DTC: AR |
| U024C:00 | Lost Communication with Seat Control Module "H": No Sub Type Information | REFER to: Pinpoint Test - DTC: AT |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | CARRY OUT the PCM self-test. REFER to the Engine Controls - Introduction (Except Diesel & Hybrid) or the appropriate service information article. Refer to the appropriate engine article for the procedure. |
| U3000:41 | Control Module: General Checksum Failure | INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| U3000:42 | Control Module: General Memory Failure | INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| U3000:54 | Control Module: Missing Calibration | Using a diagnostic scan tool, CARRY OUT the OCS Reset. FOLLOW all instructions on the diagnostic scan tool. If the OCS Reset was not successful, VERIFY correct installation of the OCS. VERIFY the pressure sensor hose is correctly routed and CORRECT the installation as necessary. REPEAT the self-test. If DTC U3000:54 is still present, INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | REFER to: Pinpoint Test - DTC: AO |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | REFER to: Pinpoint Test - DTC: AO |