Diagnostic Procedure

Step	INSPECTION		Action
1	INSPECT SEAT WEIGHT SENSOR CONTROL MODULE CONNECTOR WARNING: Handling the component parts improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings/cautions and the workshop manual before handling the air bag system components. (See AIR BAG SYSTEM SERVICE WARNINGS .) (See AIR BAG SYSTEM SERVICE CAUTIONS .) Switch the ignition to off. Disconnect the negative battery cable and wait for 1 min or more . Disconnect the seat weight sensor control module connector. (See SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Is there any malfunction of the seat weight sensor control module connector?	Yes	Repair or replace the wiring harness.
1		No	Go to the next step.
2	INSPECT SEAT WEIGHT SENSOR CONTROL MODULE POWER SUPPLY CIRCUIT Remove the front console. (See FRONT CONSOLE REMOVAL/INSTALLATION .) Disconnect all SAS control module connectors. (See SAS CONTROL MODULE REMOVAL/INSTALLATION .) Connect the negative battery cable. Switch the ignition to ON. Measure the voltage of seat weight sensor control module connector terminals 3A. NOTE: Measure the voltage while shaking the wiring harness between the seat weight sensor control module and fuse block. Is the voltage measured?	Yes	Go to the next step.
2		No	Repair the wiring harness between the seat weight sensor control module and fuse block.
3	INSPECT WIRING HARNESS Disconnect the SAS control module connector. (See SAS CONTROL MODULE REMOVAL/INSTALLATION .) Verify continuity in the following wiring harnesses: Between SAS control module terminal 2AJ and seat weight sensor control module terminal 3D Between seat weight sensor control module terminal 3B and body ground NOTE: Inspect for continuity while shaking the wiring harness between the SAS control module and seat weight sensor control module. Is the continuity normal?	Yes	Go to the next step.
3		No	If there is any malfunction in the wiring harnesses, repair or replace the applicable wiring harness. After replacement, reperform the DTC inspection and verify that no DTCs are displayed.
4	INSPECT PASSENGER SENSING SYSTEM Connect the seat weight sensor control module connector. Connect the SAS control module. Connect the negative battery cable. Verify the following PIDs using the M-MDS. (See PID/DATA MONITOR TABLE [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) OCSFLT_CAL OCSFLT_COM OCSFLT_L OCSFLT_MDL OCSFLT_R Do all PIDs display "OK"?	Yes	Go to the Step 6.
4		No	Perform the following procedures according to the M-MDS screen indication: If FAULT is displayed for OCSFLT_CAL: Perform the seat weight sensor calibration. (See SEAT WEIGHT SENSOR CALIBRATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) If FAULT is displayed for OCSFLT_COM or OCSFLT_MDL: Replace the seat weight sensor control module. (See SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) If FAULT is displayed for OCSFLT_L or OCSFLT_R: Go to the next step.
5	INSPECT SEAT WEIGHT SENSOR CONTROL MODULE Switch the ignition to off. Disconnect the negative battery cable and wait for 1 min or more . Disconnect the seat weight sensor connector from the seat weight sensor control module. Connect the negative battery cable. Switch the ignition to ON. Measure the voltage between the following terminals: CAUTION: When measuring the voltage at a terminal of the seat weight sensor control module, measure it being careful not to bend or damage the terminal. Seat weight sensor control module terminal 1A (module side) and body ground Seat weight sensor control module terminal 2A (module side) and body ground Is the voltage approx. 0 V ?	Yes	Replace the seat weight sensor control module, then go to the next step. (See SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
5		No	Replace the passenger-side front seat slide adjuster. (See FRONT SEAT SLIDE ADJUSTER REMOVAL/INSTALLATION .) Perform the DTC inspection again. If the same DTC is displayed, replace the seat weight sensor control module, then go to the next step. (See SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
6	PERFORM SAS CONTROL MODULE DTC INSPECTION Switch the ignition to off. Disconnect the negative battery cable and wait for 1min or more . Reconnect all disconnected connectors. Connect the negative battery cable. Switch the ignition to ON. Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Are the same DTCs present?	Yes	Replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION .)
6		No	DTC troubleshooting completed.