Common Specs & Procedures Index
MAZDA 6 COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | HVAC TECHNICAL DATA | ||
| Torque | See Torque Specifications in Text and applicable graphics in BASIC SYSTEM - HVAC | ||
| Axle Nut/Hub Nut | Step 1: Tighten to 74-110 Ft. Lbs. (100-150 N.m) Step 2: Loosen 180 Degrees Step 3: Tighten to 174-202 Ft. Lbs. (235-274 N.m) |
||
| Battery | BATTERY INSPECTION [SKYACTIV-G 2.5] | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF BRAKE FLUID AIR BLEEDING |
||
| Disc Brakes | |||
| Service Specifications | BRAKES TECHNICAL DATA | ||
| Torque | |||
| Front | See Torque Specifications in Text and applicable graphics in CONVENTIONAL BRAKE SYSTEM | ||
| Rear | See Torque Specifications in Text and applicable graphics in CONVENTIONAL BRAKE SYSTEM | ||
| Charging | |||
| Generator | CHARGING SYSTEM (WITH I-ELOOP) or CHARGING SYSTEM (WITHOUT I-ELOOP) | ||
| Torque | See Torque Specifications in CHARGING SYSTEM (WITH I-ELOOP) or CHARGING SYSTEM (WITHOUT I-ELOOP) | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT INSPECTION [SKYACTIV-G 2.5] | ||
| Drive Belt Routing | NA | ||
| Engine Cooling | |||
| General Service Specifications | ENGINE TECHNICAL DATA [SKYACTIV-G 2.5] | ||
| Radiator Cap Pressure | 2.5L 4-Cyl. (L5) - 16-20 psi | ||
| Thermostat R & I | |||
| 2.5L 4-Cyl. (L5) | THERMOSTAT REMOVAL/INSTALLATION [SKYACTIV-G 2.5] | ||
| Water Pump R & I | |||
| 2.5L 4-Cyl. (L5) | WATER PUMP REMOVAL/INSTALLATION [SKYACTIV-G 2.5] | ||
| Engine Mechanical | |||
| 2.5L 4-Cyl. (L5) | |||
| Compression | Standard: 954 kPa {9.73 kgf/cm2
, 138 psi}[300 rpm] Minimum: 763 kPa {7.78 kgf/cm2 , 111 psi}[300 rpm] Maximum difference between cylinders: 161 kPa {1.64 kgf/cm2 , 23.4 psi}[300 rpm] See COMPRESSION INSPECTION [SKYACTIV-G 2.5] |
||
| Oil Pressure | Lo: 16.0-25.3 psi (110-175 kPa, 1.13-1.78 kg/cm2
) at 1, 500 RPM Hi: 43.6-62.3 psi (300-430 kPa, 3.06-4.38 kg/cm2 ) at 4, 500 RPM |
||
| Overhaul | ENGINE TECHNICAL DATA [SKYACTIV-G 2.5] | ||
| Torque | See Torque Specifications in Text and applicable graphics in ENGINE MECHANICAL [SKYACTIVE-G 2.5] | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | A/T 80-85 Ft. Lbs. (108-116 N.m) M/T 113-118 (152-160 N.m) |
||
| Fuel System | |||
| Pressure Specification | 2.5L 4-Cyl. (L5) 58.8-70.3 psi (405-485 kPa, 4.13-4.94 kg/cm2 | ||
| Fuel Pressure Test Procedure | For 2.5L, See FUEL LINE PRESSURE INSPECTION [SKYACTIV-G 2.5] | ||
| Fuel Filter Location And R & I | Fuel filter is an integral attachment of Fuel Pump Unit assembly. See FUEL PUMP UNIT REMOVAL/INSTALLATION [SKYACTIV-G 2.5] . | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 2.5L engine is equipped with coil-on-plug ignition. | ||
| Ignition Wires (Routing) | 2.5L engine is equipped with coil-on-plug ignition. | ||
| Spark Plug | |||
| 2.5L 4-Cyl. (L5) (PE5R-18-110, PE5S-18-110) | |||
| Gap | SPARK PLUG INSPECTION [SKYACTIV-G 2.5] | ||
| Torque | 12-14 ft. lb. (15-20 N.m) | ||
| Starting | |||
| Starter | 2.5L - STARTER INSPECTION [SKYACTIV-G 2.5] | ||
| Torque | 2.5L - See Torque Specifications in Text and applicable graphics in STARTER REMOVAL/INSTALLATION [SKYACTIV-G 2.5] . | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT | ||
| Torque | See Torque Specifications in Text and applicable graphics in WHEEL ALIGNMENT | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 80-108 Ft. Lbs. (108-147 N.m) | ||