Section 2494 (Engine - Repair (N54))
WARNING: This page is about a different car, the 2010 BMW X6, 2009 BMW X6, and 2008 BMW X6. However, it is still accessible from the selected car via links, so may be relevant.
- Engine General
- 00 Danger of poisoning if oil is ingested/absorbed through the skin
- Protective measures/rules of conduct
- First aid measures
- 00 Risk of injury if oil comes into contact with eyes and skin
- 00 Safety instructions for handling oil
- Recycling
- 11 00 Mounting engine on assembly stand (N54)
- 11 00 Removing and installing/replacing front ignition coil cover (N54)
- 11 00 Removing and installing/replacing ignition coil cover (N54)
- 11 00 Removing and installing/replacing rear ignition coil cover (N54)
- 11 00... Overview of consumables
- 11 00... Service - engine oil (N54)
- 11 00 039 Checking compression in all cylinders (N43/ N53/ N54)
- 11 00 050 Removing and installing engine (N54)
- 11 00 590 Replacement power plant (N54)
- 11 00 670 Securing engine in installation position (N54)
- Engine identification
- Cylinder Head And Cylinder Head Cover
- Oil Sump
- Housing Cover
- Crankshaft With Bearing
- Flywheel
- Vibration Damper
- Connecting Rod With Bearing
- Piston With Rings And Pin
- V-Ribbed Belt With TENSIONER
- Camshaft
- 11 31 005 Checking camshaft timing (N54)
- 11 31 025 Removing and installing or replacing inlet camshaft (N54)
- 11 31 028 Removing and installing or replacing exhaust camshaft (N54)
- 11 31 051 Replacing timing chain (N54)
- 11 31 090 Installing and removing/replacing chain tensioner piston (N54)
- 11 31 505 Adjusting camshaft timing (N54)
- Rocker Arm With Bearing Mount
- Valves With Springs
- Variable Camshaft Timing
- Oil Supply
- Oil Pump With Filter
- Oil Filter And Lines
- 11 42 020 Removing and installing/replacing fullflow oil filter (N54)
- 11 42 198 Removing and installing oil feed line for exhaust turbocharger (N54)
- 11 42 250 Removing and installing oil return line for exhaust turbocharger (N54)
- 11 42 248 Removing and installing/renewing the oil return line for exhaust turbocharger cyl. 1-3 (N54)
- 11 42 035 Removing and installing/replacing thermostat housing (N54, N54T)
- Oil Cooler
- Water Pump With Drive
- Thermostat And Connector
- Intake Manifold
- 11 61 050 Removing and installing intake air manifold (N54)
- 11 61 362 Replacing right charge-air duct (N54)
- 11 61 365 Replacing front charge-air duct (N54)
- 11 61 368 Removing and installing/replacing rear left charge-air duct (N54)
- 11 61 368 Replacing charge-air duct (N54)
- 11 61 730 BMW leak test for intake system (N54)
- Notes
- Vacuum pressure measurement
- Calibration for vacuum pressure measurement
- Connections on EPPC
- Checking wastegate on cylinders 1-3
- Checking wastegate on cylinders 4-6
- Checking flap of vacuum unit (wastegate valve)
- Pressure measurement
- Checking blow-off valves
- Checking activation of blow-off valves with EPPC
- Supercharger
- 11 65 164 Removing and installing/replacing both blow-off valves (N54)
- 11 65 Connection diagram, vacuum activation (N54)
- 11 65... Removing and installing vacuum unit (wastegate valve) for cylinders 4-6 (N54)
- 11 65 022 Removing and installing/replacing exhaust-gas turbocharger for cylinders 1-3 (N54)
- 11 65 024 Removing and installing/replacing exhaust-gas turbocharger for cylinders 4-6 (N54)
- 11 65 580 Replacing vacuum unit (wastegate valve) (N54)
- Vacuum Pump
- Emission Control Oxygen Sensor