LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mitsubishi >> 2003 >> Eclipse RS, Standard >> Repair and Diagnosis (Single Page) >> Engine Performance >> System >> Engine Controls - Self-Diagnostics - 2.4L >> Diagnostic Tests >> DTC P0122: Throttle Position (TP) Sensor Circuit Low Input >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

CAUTION: To prevent damage to scan tool (MB991502), always turn the ignition off before connecting or disconnecting it.
  1. Connect scan tool (MB991502) to the data link connector. Turn the ignition on. Set the scan tool to data reading mode for item 14, Throttle Position Sensor. With the throttle valve in the idle position, voltage should be between 0.535-0.735 volt. With the throttle valve in the full-open position, voltage should be between 4.5-5.5 volts. Turn the ignition off. If the sensor is operating properly, it can be assumed that this malfunction is intermittent, see INTERMITTENT DIAGNOSTIC TROUBLE CODES  . If the sensor is malfunctioning, go to the next step.
  2. Check connector B-07 at throttle position sensor for damage. If the connector is in good condition, go to the next step. If the connector is damaged, repair or replace it and proceed to step  11 .
  3. Check the sensor supply voltage at throttle position sensor harness side connector B-07. Disconnect the connector B-07 and measure at the harness side. Turn the ignition on. Measure the voltage between terminal No. 4 and ground. Voltage should be between 4.8-5.2 volts. Turn the ignition off. If the voltage is normal, proceed to step  6 , otherwise, go to the next step.
  4. Check connector C-60 at ECM (M/T) or connector C-54 at PCM (A/T) for damage. If the connector is in good condition, go to the next step. If the connector is damaged, repair or replace it and proceed to step  11 .
  5. Check for open circuit and short circuit to ground between throttle position sensor connector B-07 (terminal No. 3) and ECM connector C-60 (terminal No. 81 - M/T) or PCM connector C-54 (terminal No. 46 - A/T). If the harness wire is in good condition, replace the ECM or PCM. If the harness wire is damaged, repair it. Proceed to step  11 .
  6. Check the throttle position sensor. Disconnect the connector B-07. Measure the resistance between throttle position sensor side connector terminals No. 1 and 4. Standard value: 3.5-6.5 k/ohms. Measure the resistance between the throttle position sensor side connector terminals No. 1 and 3. Move the throttle valve from the idle position to the full-open position. Resistance should change smoothly in proportion to the opening angle of the throttle valve. If the resistance is normal, go to the next step. If the resistance is abnormal, replace the throttle position sensor, refer to THROTTLE BODY ASSEMBLY in REMOVAL & INSTALLATION article; and proceed to step  11 when finished.
  7. Check connector C-60 at ECM (M/T) or connector C-54, C-57 at PCM (A/T) for damage. If the connector is in good condition, go to the next step. If the connector is damaged, repair or replace it and proceed to step  11 .
  8. Check for open circuit and short circuit to ground between throttle position sensor connector B-07 (terminal No. 1) and ECM connector C-60 (terminal No. 84 - M/T) or PCM connector C-57 (terminal No. 78 - A/T). If the harness wire is in good condition, go to the next step. If the harness wire is damaged, repair it and proceed to step  11 .
  9. Check for short circuit to ground between throttle position sensor connector and auto-cruise control-ECU. If the harness wire is in good condition, go to the next step, otherwise, repair it and proceed to step  11 .
  10. Connect scan tool (MB991502) to the data link connector. Turn the ignition on. Set the scan tool to data reading mode for item 14, Throttle Position Sensor. With the throttle valve in the idle position, voltage should be between 0.535-0.735 volt. With the throttle valve in the full-open position, voltage should be between 4.5-5.5 volts. Turn the ignition off. If the sensor is operating properly, it can be assumed that the malfunction is intermittent, see INTERMITTENT DIAGNOSTIC TROUBLE CODES  . If the sensor is malfunctioning, replace the ECM or PCM and go to the next step.
  11. Carry out a test drive with the drive cycle pattern, refer to OTHER MONITOR  . Check the diagnostic trouble codes. If DTC P0122 is output, retry the troubleshooting. If the DTC is absent, the inspection is complete.
scientia non olet · About LEMON Manuals