DTC U1100: CAN Communications System Time Out Error Engine Related Data: Diagnosis

Required Special Tools:

MB991958: Scan tool (MUT-III sub assembly)
- MB991824: V.C.I.
- MB991827: MUT-III USB cable
- MB991910: MUT-III main harness A

STEP 1. Using scan tool MB991958, diagnose the CAN bus line.
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
  
  Fig 1: Connecting Scan Tool MB991958 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
3. Diagnose the CAN bus line. (Refer to EXPLANATION ABOUT THE MUT-III CAN BUS DIAGNOSIS ).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991958.
Q: Is the CAN bus line found to be normal?

YES: Go to Step 2.

NO: Repair the CAN bus line. (Refer to DIAGNOSTIC TROUBLE CODE DIAGNOSIS , ). Then go to Step 6.
STEP 2. Using scan tool MB991958, read the diagnostic trouble code.
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
  
  Fig 2: Connecting Scan Tool MB991958 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
3. Check for MFI system diagnostic trouble code. (Refer to HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODE , ).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991958.
Q: Is any DTC set?

YES: Repair the MFI control system. (Refer to DIAGNOSTIC TROUBLE CODE CHART ). Then go to Step 6.

NO: Go to Step 3.
STEP 3. Using scan tool MB991958, read the diagnostic trouble code.
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
  
  Fig 3: Connecting Scan Tool MB991958 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
3. Check if a DTC, which relates to CAN communication-linked systems below, is set.
  1. ETACS-ECU
    - DTC 011: Power train control module time-out (related to engine)
  2. Combination meter
    - DTC 011: Power train control module time-out (related to engine)
  3. Multi-center display
    - DTC 011: Power train control module time-out (related to engine)
  4. A/C-ECU
    - DTC U1100: Power train control module time-out (related to engine)
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991958.
Q: Is DTC 011 or U1100 set?

YES: Go to Step 4.

NO: Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set.

CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool .MB991958.
1. Connect scan tool MB991958 to the data link connector. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
  
  Fig 4: Connecting Scan Tool MB991958 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
3. Erase the DTC. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Turn the ignition switch to the "ON" position.
6. Check if the DTC is set.
7. Turn the ignition switch to the "LOCK" (OFF) position.
8. Disconnect scan tool MB991958.
Q: Is DTC U1100 set?

YES: Replace the PCM. Refer toPOWERTRAIN CONTROL MODULE (PCM) , . Then go to Step 6.

NO: It can be assumed that this malfunction is intermittent. (Refer to HOW TO COPE WITH INTERMITTENT MALFUNCTIONS ).
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set.

CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
  
  Fig 5: Connecting Scan Tool MB991958 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
3. Erase the DTC. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Turn the ignition switch to the "ON" position.
6. Check if the DTC is set.
7. Turn the ignition switch to the "LOCK" (OFF) position.
8. Disconnect scan tool MB991958.
Q: Is DTC U1100 set?

YES: Replace the hydraulic unit (integrated with ABS/TCL-ECU < FWD > or TCL/ASC-ECU < AWD >). (Refer to HYDRAULIC UNIT ). Then to Step 6.

NO: It can be assumed that this malfunction is intermittent. (Refer to HOW TO COPE WITH INTERMITTENT MALFUNCTIONS ).
STEP 6. Recheck for diagnostic trouble code.
Check again if the DTC is set.

CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
  
  Fig 6: Connecting Scan Tool MB991958 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
3. Erase the DTC. (Refer to TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS ).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Turn the ignition switch to the "ON" position.
6. Check if the DTC is set.
7. Turn the ignition switch to the "LOCK" (OFF) position.
8. Disconnect scan tool MB991958.
Q: Is DTC U1100 set?

YES: Return to Step 1.

NO: The procedure is complete.