Inspection Procedure 5: Combination Meter Does Not Work.: Diagnosis

Required Special Tool: 

• MB991223: Harness Set

1. STEP 1. Measure at combination meter connector C-02 in order to check the battery circuit of power supply system to the combination meter. 
   1. Disconnect combination meter connector C-02, and measure at the wiring harness side.
      Fig 1: Identifying Connector C-02

      Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   2. Measure the voltage between terminal 7 and ground.
   • The measured value should be approximately 12 volts (battery positive voltage).

   Q: Does the measured voltage correspond with this range? 

   1. YES:  Go to  Step 4.
   2. NO:  Go to Step 2.
   Fig 2: Measuring The Voltage Between Terminal 7 And Ground

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. STEP 2. Check combination meter connector C-02 for damage. 

   Q: Is combination meter connector C-02 in good condition? 

   1. YES:  Go to Step 3.
   2. NO:  Repair or replace the connector. Refer to HARNESS CONNECTOR INSPECTION . Check to see that all meters operate.
   Fig 3: Locating Connector C-02

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. STEP 3. Check the wiring harness between combination meter connector C-02 (terminal 7) and battery. 
   Fig 4: Identifying Connector C-02

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   NOTE: Also check intermediate connector C-124. If intermediate connector (1) C-09. If intermediate connectors C-124 or joint connector (1) C-09 is damaged, repair or replace the connector as described in HARNESS CONNECTOR INSPECTION .

   Q: Are the wiring harness between combination meter connector C-02 (terminal 7) and battery in good condition? 

   1. YES:  There is no action to be taken.
   2. NO:  Repair the wiring harness. Check to see that all meters operate.
   Fig 5: Identifying Fusible Links

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   Fig 6: Identifying Connector Terminals

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. STEP 4. Measure at combination meter connector C-02 in order to check the battery circuit of power supply system to the combination meter. 
   1. Disconnect combination meter connector C-02, and measure at the wiring harness side.
   2. Turn the ignition switch to "ON" position.
      Fig 7: View Of Connector C-02

      Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   3. Measure the voltage between terminal 9 and ground.
   • The measured value should be approximately 12 volts (battery positive voltage).

   Q: Does the measured voltage correspond with this range? 

   1. YES:  Go to  Step 7.
   2. NO:  Go to Step 5.
   Fig 8: Measuring Voltage Between Terminal 9

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. STEP 5. Check combination meter connector C-02 for damage. 

   Q: Is combination meter connector C-02 in good condition? 

   1. YES:  Go to Step 6.
   2. NO:  Repair or replace the connector. Refer to HARNESS CONNECTOR INSPECTION . Check to see that all meters operate.
   Fig 9: Locating Connector C-02

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
6. STEP 6. Check the wiring harness between combination meter connector C-02 (terminal 2) and ignition switch (IG1). 
   Fig 10: View Of Connector C-02

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   NOTE: Also check junction block connectors C212, C-215 and joint connector (5) C-03. If junction block connectors C-212, C-215 or joint connector (5) C-03 are damaged, repair or replace the connector as described in HARNESS CONNECTOR INSPECTION .

   Q: Are the wiring harness between combination meter connector C-02 (terminal 9) and ignition switch (IG1) in good condition? 

   1. YES:  There is no action to be taken.
   2. NO:  Repair the wiring harness. Check to see that all meters operate.
   Fig 11: Identifying Connector Terminals

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   Fig 12: Identifying Connector C-03

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
7. STEP 7. Measure at combination meter connector C-02 in order to check the ground circuit to the combination meter. 
   1. Disconnect combination meter connector C-02, and measure at the wiring harness side.
      Fig 13: Locating Connector C-02

      Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
   2. Measure the resistance between terminal 1 and ground.
      • The measured value should be 2 ohms or less.
   3. Measure the resistance between terminal 2 and ground.
      • The measured value should be 2 ohms or less.

   Q: Does the measured voltage correspond with this range? 

   1. YES:  Repair the combination meter. Check to see that all meters operate.
   2. NO:  Go to Step 8.
   Fig 14: Measuring Resistance Between Terminal 1, 2 And Ground

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
8. STEP 8. Check combination meter connector C-02 for damage. 

   Q: Is combination meter connector C-02 in good condition? 

   1. YES:  Go to Step 9.
   2. NO:  Repair or replace the connector. Refer to HARNESS CONNECTOR INSPECTION . Check to see that all meters operate.
   Fig 15: Locating Connector C-02

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
9. STEP 9. Check the wiring harness between combination meter connector C-02 (terminal 1 and 2) and ground. 

   Q: Are the wiring harness between combination meter connector C-02 (terminal 1 and 2) and ground in good condition? 

   1. YES:  There is no action to be taken.
   2. NO:  Repair the wiring harness. Check to see that all meters operate.
   Fig 16: Identifying Connector C-02

   Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.