Pcm Reprogramming For DTC P0335 / P0340 (TSB-06-13-006REV)

Publication date: 2006-07-01
Reference number: TSB-06-13-006REV
Supersedes refnos: TSB-06-13-006

PCM REPROGRAMMING FOR DTC P0335 / P0340

TECHNICAL SERVICE BULLETIN

Reference Number(s): TSB-06-13-006REV, Date of Issue: July 01, 2006

MITSUBISHI:

See below

Superceded Bulletin(s): TSB-06-13-006, Date of Issue: July 01, 2006

NOTE: This bulletin supercedes TSB-06-13-006, to add 2004 Lancer, include procedures for MEDIC-II and update the Warranty Information section

PURPOSE

On some affected vehicles, incorrect software parameters in the PCM may cause the MIL to illuminate and Diagnostic Trouble Code P0335 and/or P0340 (crankshaft or camshaft position sensor circuit) to set in the PCM. To eliminate this condition, reprogram the PCM as described in this bulletin.

AFFECTED VEHICLES

2004-2006 Lancer

2005-2006 Outlander

2006-2007 Eclipse

2007 Eclipse Spyder

2006 Galant

PROCEDURE

CAUTION: BATTERY VOLTAGE (AS MEASURED AT THE BATTERY POSTS WITHOUT ELECTRICAL LOAD) MUST BE 12.4V OR HIGHER IN ORDER TO REPROGRAM THE PCM.

IMPORTANT: Verify whether the vehicle is K-Line Flash or CAN-Flash. Refer to the "Reprogramming System Identification. chart on the Service Tech Resources page on the Mitsubishi Dealer Link. The procedure for PCM reprogramming on CAN-Flash vehicles is different than K-Line Flash vehicles. Be sure to follow the correct reprogramming instructions for the vehicle being repaired.

Check the underside of the hood to verify that there is no label previously installed to indicate that this TSB reprogramming has already been done.
Using the MUT-III, verify that the vehicle's ECU part number is listed in the table in Step 7. If the Software P/N is the same as or higher than the Software P/N in the table, the PCM has already been reprogrammed for this concern. Do not continue with this bulletin procedure. Refer to Group 13 in the appropriate service manual to diagnose the DTC.
Use the MUT-III to erase all DTCs set in the PCM.
MEDIC-II ONLY . Verify that your MEDIC-II is at download M118 or higher.
NOTE: Dealers using MEDIC-II will not receive a reflash CD. The reflash data will be sent electronically.
1. If the download version is M118 or higher, go to step 5.
  
  Fig 1: MUT-III Scan Tool - Download Version Number
2. If the download version is less than M118, force a download to the MEDIC-II as follows:
  1. On the MEDIC-II main screen, click on "Maintenance."
    
    Fig 2: MUT-III Scan Tool - Click On Maintenance
  2. Click on "Download."
    
    Fig 3: MUT-III Scan Tool - Click On Download
Transfer the reprogramming data from the MEDIC-II laptop to the memory card. (Use the port on the left side of the MUT-III laptop.) Select ECU Reprogramming , then Memory Card Transfer . A status bar will display while the data is loading into the memory card.
When the memory card data transfer is complete, remove the memory card from the laptop and install it in the VCI. Then go to step 7 for CAN-FLASH VEHICLES ONLY or step 8 FOR K-LINE FLASH VEHICLES.
Scan Tool Viewer (STV) ONLY. Verify that your MUT-III is at STV Version 13.1 or higher, and that it has the most current version of the reprogramming database:
1. Select "Special Function", then select "ECU Reprogramming."
2. Select "Database File Display." The database version is displayed in the top right corner of the screen. Make sure the database version is N06061 or greater .
3. If the database version is N06061 or greater, reprogram the PCM as described in Step 7 for CAN-FLASH VEHICLES ONLY or step 8 for K-LINE FLASH VEHICLES .
4. If the database version is less than N06061 , you must transfer the new reprogramming data from the Reflash Update CD 7/06 to the MUT-III hard drive as follows:
  1. Install Reflash Update CD 7/06 into the PC's DVD-ROM drive.
  2. Follow the instructions on the screen. The system will automatically transfer the reprogramming data onto the PC's hard drive.
    
    Fig 4: MUT-III Scan Tool - Reflash Update CD 7/06
CAN-FLASH VEHICLES ONLY:
IMPORTANT: DO NOT DISCONNECT THE MEDIC-II LAPTOP. DO NOT USE VCI STANDALONE REPROGRAMMING.

The following equipment is required for PCM reprogramming on CAN-Flash vehicles:
- MUT-III PC
- Reprogramming Database on DVD-ROM (Reflash Update CD 7/06 or later for this concern)
- VCI (Vehicle Communication Interface) - MB991824
- MUT-III main harness A (blue) - MB991910
- USB 2.0 cable - MB991827
- "Engine Compartment/Control Module" labels - p/n MSSF-024G-00
Connect this equipment in the same manner as for normal vehicle diagnosis. When reprogramming a CAN-Flash vehicle, the VCI and MUT-III laptop must be connected. DO NOT use VCI Standalone on CAN-Flash vehicles.
1. In the MUT-III System Select menu, click on the car symbol at the bottom of the screen.
  
  Fig 5: MUT-III Scan Tool - Select VIN
  
  Select VIN. Then type in the VIN.
2. Connect the VCI to the vehicle. DO NOT DISCONNECT THE LAPTOP.
3. Select "Special Function."
  
  Fig 6: MUT-III Scan Tool - Select Special Function
4. Select "ECU reprogramming."
  
  Fig 7: MUT-III Scan Tool - Select ECU Reprogramming
5. Select "Automatic Reprogramming (CAN)."
  
  Fig 8: MUT-III Scan Tool - Select Automatic Reprogramming (CAN)
6. Select Engine and Transmission, then click on the check mark.
  A message will advise you that the system will "Automatic Search the data."
  
  Click on the check mark to continue.
  
  Fig 9: MUT-III Scan Tool - Select Engine And Transmission
  
  If the PCM is already reprogrammed for this concern, this screen will display. If this message displays, do not continue with this reprogramming procedure.
  
  CAUTION: DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS. INTERRUPTION DURING THE PROGRAMMING PROCESS COULD CAUSE THE PCM TO LOSE DATA OR PREVENT FUTURE PCM REPROGRAMMING.
  
  Fig 10: MUT-III Scan Tool - "Already Reprogramed" Screen
7. The CAN database screen will display.
  (If more than one row is displayed in the table, select the appropriate ECU part number.)
  
  Click on the check mark to begin reprogramming.
  
  NOTE: It will take up to 10 minutes to complete the reprogramming.
  
  Fig 11: MUT-III Scan Tool - CAN Database Screen Display
8. This message will display when the reprogramming is successfully completed.
  Go to Step 7 to complete this bulletin procedure.
  
  Fig 12: MUT-III Scan Tool - "Reprogramming Successful" Screen
K-LINE FLASH VEHICLES ONLY:
1. If you just transferred the new reprogramming data from the Reflash Update CD 7/06 to the MUT-III hard drive, now transfer the reprogramming data from the MUT-III laptop to the memory card. (Use the port on the left side of the MUT-III laptop.) Select ECU Reprogramming , then Memory Card Transfer . A status bar will display while the data is loading into the memory card.
  When the memory card data transfer is complete, remove the memory card from the laptop and install it in the VCI.
2. Connect the following equipment in the same manner as for normal vehicle diagnosis:
  - VCI (Vehicle Communication Interface) - MB991824
  - MUT-III main harness B (red) - MB991911
  - Outlander models only: 12-13 pin adapter MB991855
  Fig 13: ECU Programing Components
3. IMPORTANT: Lancer and Outlander models equipped with ABS: With the ignition key OFF, unplug the ABS fuse (7.5 amp fuse in the junction box in the passenger compartment ). Refer to the service manual for exact fuse location in the box.
4. Reprogram the PCM, using "Automatic reprogramming " on the VCI. It will take up to 20 minutes to complete the reprogramming.
  CAUTION: DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS. INTERRUPTION DURING THE PROGRAMMING PROCESS COULD CAUSE THE PCM TO LOSE DATA OR PREVENT FUTURE PCM REPROGRAMMING.
  
  If the message "ECU at Current Level of VCI" appears, the PCM did not reprogram. Verify that the ROM ID is the same as the ROM ID listed in the table in Step 7.
  - If the ROM ID is the same or higher than the ROM ID in the table, the PCM has already been reprogrammed for this concern. Do not continue with this reprogramming procedure.
  - If it is not, verify that the correct database update is in the MUT-III. Verify the correct database was transferred to the memory card, and that the memory card is properly installed in the VCI.

After reprogramming, the new ECU part number and software part number will display. Verify that they are the same as those listed below. Note this information.

ECU P/N REFERENCE CHART

			DISPLAY ON MUT-III AFTER REPROGRAMMING
MODEL	ECU P/N	MUT-III REFLASH DATABASE	ECU P/N	Software P/N (ROM ID)	VENDOR #
2007 Eclipse 2.4L MIVEC A/T	8631A301	1862A568	8631A301	8631A301BA	E6T45277H10
2007 Eclipse/Eclipse Spyder 3.8L MIVEC A/T	8631A149	1862A567	8631A149	8631A149BA	E6T45376H10
2007 Eclipse Spyder 2.4L MIVEC A/T	8631A148	1862A566	8631A148	8631A148BA	E6T45276H10
2007 Eclipse/Eclipse Spyder 3.8L MIVEC M/T	1860A516	1862A565	1860A516	1860A516BB	E6T45375H1
2007 Eclipse/Eclipse Spyder 2.4L MIVEC M/T	1860A515	1862A564	1860A515	1860A515BB	E6T45275H1
2006 Eclipse 3.8L A/T	1860A220	1862A557	1860A220	1860A220FC	E6T45374H2
2006 Eclipse 3.8L MIVEC M/T	1860A219	1862A556	1860A219	1860A219FF	E6T45373H5
2006 Eclipse 2.4L MIVEC M/T	1860A217	1862A554	1860A217	1860A217CC	E6T45273H2
2006 Eclipse 2.4L MIVEC A/T	1860A218	1862A553	1860A218	1860A218CC	E6T45274H22
2006 Galant 2.4L MIVEC A/T Calif. emissions	1860A316	1862A552	1860A316	1860A316CA	E6T41683H20
2006 Galant 2.4L MIVEC A/T Federal emissions	1860A315	1862A551	1860A315	1860A315CA	E6T41682H20
2006 Lancer 2.4L MIVEC M/T	1860A420	VN06016	1860A420	C82810	E6T34899H1
2006 Lancer/Lancer Sportback 2.4L MIVEC A/T	1860A421	VN06015	1860A421	E82911	E6T37979H10
2005 Lancer 2.4L MIVEC M/T	1860A070	VN0602D	1860A070	C71320	E6T34891H3
2004 Lancer 2.4L MIVEC M/T	MN156916	VN0605A	MN156916	C52414	E6T34885H2

ECU P/N REFERENCE CHART

MODEL	ECU P/N	MUT-III REFLASH DATABASE	ECU P/N	Software P/N (ROM ID)	VENDOR #
2006 Outlander 2.4L MIVEC M/T 4WD	1860A473	VN0601A	1860A473	C84611	E6T38990H1
2006 Outlander 2.4L MIVEC M/T 2WD	1860A472	VN06019	1860A472	C84511	E6T38989H1
2006 Outlander 2.4L MIVEC A/T 4WD	8631A118	VN06018	8631A118	E84810	E6T45579H10
2006 Outlander 2.4L MIVEC A/T 2WD	8631A117	VN06017	8631A117	E84710	E6T45578H10
2005 Outlander 2.4L MIVEC M/T 4WD	1860A149	VN0602H	1860A149	C71520	E6T38981H3
2005 Outlander 2.4L MIVEC M/T 2WD	1860A148	VN0602G	1860A148	C71420	E6T38980H3

Turn the ignition switch to OFF. Disconnect the MUT-III from the vehicle. Wait at least 10 seconds , then start the engine to verify proper operation.
Using a ball-point pen, enter the appropriate PCM part number, vendor number, ROM ID, this TSB number (TSB-06-13-006), your dealer code, and the current date on the Engine Compartment and Control Module Label (part no. MSSF-024G-00).

Fig 14: MUT-III Scan Tool - Engine Compartment and Control Module Label
Carefully remove all dirt and oil from a vacant area near the VECI label on the underside of the hood, and affix the Engine Compartment label.
Affix the Control Module Label to the PCM.
Lancer and Outlander models equipped with ABS: Reconnect the ABS fuse. Confirm no DTC is set.
Test drive the vehicle to confirm proper operation and no MIL illumination.

WARRANTY INFORMATION

Special Value Field Entry Required: Enter the applicable DTC code(s) found during diagnosis in the Spec Value field.

The Spec Value field is located below the "Condition, Cause & Remedy" fields"

Spec Value*

PCM Reprogramming for DTC P0335 / P0340

PCM REPROGRAMMING REFERENCE

Nature Code: 99D	Cause Code: 490
Labor Operation No. 13850195	Time Allowance: 0.3 hr.
Warranty Coverage: 8 years / 80,000 miles

Special Warranty Information: Claims submitted without the applicable DTC code(s) entered in the Spec Value field are subject to charge back. Normal warranty procedures apply.