Specifications Index
LANCER (EVOLUTION) SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SPECIFICATION | ||
| Torque | FASTENER TIGHTENING SPECIFICATION | ||
| Axle Nut/Hub Nut | |||
| Front | 226 +/- 29 N.m (167 +/- 21 ft-lb) | ||
| Rear | 225 +/- 25 N.m (166 +/- 18 ft-lb) | ||
| Battery | ON-VEHICLE SERVICE | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | See GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes (Parking Brake) | |||
| Service Specifications | See GENERAL SPECIFICATIONS , SERVICE SPECIFICATIONS and PARKING BRAKE LINING AND DRUM . | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | 7. DRIVE BELT (FOR GENERATOR, WATER PUMP AND POWER STEERING OIL PUMP) (CHECK CONDITION) | ||
| Belt Routing | 7. DRIVE BELT (FOR GENERATOR, WATER PUMP AND POWER STEERING OIL PUMP) (CHECK CONDITION) | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14 - 18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 250 r/min): 1,000 kPa (145 psi). Minimum limit (at engine speed of 200 r/min): 637 kPa (92 psi). | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more At 3,500 r/min: 294 - 686 kPa (43 - 100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 132+/- 5 N.m (98 +/- 3 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 230 kPa (67.9 in. Hg) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | SPARK PLUG CABLE RESISTANCE CHECK | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| Type | NGK; ILFR7H | ||
| Gap | 0.020-0.024 in. (0.5-0.6 mm) | ||
| Torque | 25 +/- 5 N.m (18 +/- 4 ft-lb). | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS and REMOVAL AND INSTALLATION | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 ft. lbs. (98+/-10 N.m) | ||