Chassis Electrical
- Battery
- Ignition Switch*
- Immobilizer System
- General Description
- Encrypted Code Registration Criteria Table
- Immobilizer System Diagnosis
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Symptom Chart
- Symptom Procedures
- Data List Reference Table
- Check At ETACS-Ecu (Immobilizer-Ecu) Terminal
- Special Tools
- On-Vehicle Service
- Key Ring Antenna
- ETACS-Ecu
- Combination Meter Assembly
- General Description
- Combination Meters Diagnosis
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Defective odometer
- DTC B1201: Defective fuel gauge
- DTC U1073: Bus off
- DTC U1100: ECM < M/T> or PCM < A/T> time-out (related to engine)
- DTC U1101: PCM time-out (related to A/T) < A/T>
- DTC U1102: ABS-ECU time-out
- DTC U1109: ETACS-ECU time-out
- DTC U1112: SRS-ECU time-out
- DTC U1114: TPMS-ECU time-out
- DTC U1120: Failure information on ECM < M/T> or PCM < A/T> (related to engine)
- DTC U1206: Flag invalid
- DTC U1434: Failure information on TPMS-ECU
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication with scan tool is not possible
- INSPECTION PROCEDURE 2: Power supply circuit, INSPECTION PROCEDURE 3: Odometer and trip meter are not displayed, INSPECTION PROCEDURE 4: All the needle meters do not work, INSPECTION PROCEDURE 5: When the ignition switch is turned to the ON position, the indicator and warning lights do not illuminate
- INSPECTION PROCEDURE 6: Speedometer does not work (other meters work), INSPECTION PROCEDURE 7: The fuel gauge needle moves excessively
- INSPECTION PROCEDURE 8: Tachometer does not work (other meters work)
- INSPECTION PROCEDURE 9: Fuel gauge does not work (other meters work)
- INSPECTION PROCEDURE 10: Engine coolant temperature gauge does not work (other meters work)
- INSPECTION PROCEDURE 11: The Fuel Warning Light does not Illuminate or go out
- Data List Reference Table
- Actuator Test Reference Table
- Combination Meter Terminal Check
- Special Tools
- On-Vehicle Service
- Headlight, Front Side Marker Light And Position Light Assembly
- Fog Light
- Rear Combination Light
- Dome Light
- Hazard Warning Light Switch
- Column Switch
- Horn
- Accessory Socket
- Radio With Cd Player
- General Description
- Radio With Cd Player, Speaker And Antenna Diagnosis
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When power switch is turned "ON," no power is available
- INSPECTION PROCEDURE 2: Remote controlled radio switch: When remote controlled radio power switch is turned "ON," no power is available. But radio and CD player with CD changer power switch is available. < Vehicles with audio amplifier>
- INSPECTION PROCEDURE 3: Remote controlled radio switch: The system does not recognize the remote controlled radio switch (RH) only. < Vehicles with audio amplifier>
- INSPECTION PROCEDURE 4: Remote controlled radio switch: The system does not recognize the remote controlled radio switch (LH) only. < Vehicles with audio amplifier>
- INSPECTION PROCEDURE 5: No Sound. < Vehicles with audio amplifier>
- INSPECTION PROCEDURE 6: No sound from one speaker. < Vehicles without audio amplifier>
- INSPECTION PROCEDURE 7: No sound from door speaker or woofer. < Vehicles with audio amplifier>
- INSPECTION PROCEDURE 8: No sound from tweeter or quarter speaker. < Vehicles with audio amplifier>
- INSPECTION PROCEDURE 9: Noise: Noise is present while moving (AM)
- INSPECTION PROCEDURE 10: Noise: Noise is present while moving (FM)
- INSPECTION PROCEDURE 11: Noise: Sound mixed with noise, only at night (AM)
- INSPECTION PROCEDURE 12: Noise: Noise is overpowering both AM and FM
- INSPECTION PROCEDURE 13: Noise: Excessive noise on AM and FM
- INSPECTION PROCEDURE 14: Noise: Noise is detected with engine running
- INSPECTION PROCEDURE 15: Noise: Noise appears during vibration or shocks
- INSPECTION PROCEDURE 16: Noise: Noise is present while moving (FM)
- INSPECTION PROCEDURE 17: Noise: Constant noise
- INSPECTION PROCEDURE 18: Radio: No reception (AM)
- INSPECTION PROCEDURE 19: Radio: Poor reception
- INSPECTION PROCEDURE 20: Radio: Distortion on AM and/or FM
- INSPECTION PROCEDURE 21: Radio: Distortion on FM only
- INSPECTION PROCEDURE 22: Radio: Auto select function inoperative, too few automatic stations are selected
- INSPECTION PROCEDURE 23: Radio: Preset stations are erased
- INSPECTION PROCEDURE 24: CD player, CD auto changer: CD can not be Inserted
- INSPECTION PROCEDURE 25: CD player, CD auto changer: No sound (CD only)
- INSPECTION PROCEDURE 26: CD player, CD auto changer: CD sound skips
- INSPECTION PROCEDURE 27: CD player, CD auto changer: Sound quality is poor
- INSPECTION PROCEDURE 28: CD player, CD auto changer: CD cannot be ejected
- Special Tool
- Remote Controlled Radio Switch < Vehicles With Audio Amplifier>
- Speaker
- Amplifier
- Defogger
- Multi-Center Display
- General Description
- Diagnosis
- Symptom Procedures
- INSPECTION PROCEDURE 1: The multi-center display does not Show any Information
- INSPECTION PROCEDURE 2: "-" (Ambient air temperature sensor error) is displayed on the ambient air temperature display. < Vehicles with TYPE 1>
- INSPECTION PROCEDURE 3: The ambient air temperature display does not change normally. < Vehicles with TYPE 1>
- INSPECTION PROCEDURE 4: On the Audio Screen, "E" cannot Proceed to Next Screen
- INSPECTION PROCEDURE 5: The Compass can not be Calibrated Manually, or Goes Out of Calibration Easily. < Vehicles with TYPE 1>
- Check At Multi-Center Display Unit Terminal
- Special Tools
- On-Vehicle Service < Vehicles With Type 1>
- Ambient Air Temperature Sensor
- Theft Alarm
- Specifications