F.A.S.T. Key Programming (MTT-0607-04)

F.A.S.T. KEY PROGRAMMING

TECHNICAL INFORMATION TIP - MANUFACTURER

SERVICE INFORMATION

F.A.S.T. Key Programming  - 2007 Outlander, 2008 Lancer  . Programming the F.A.S.T. key system for vehicle starting and entry  requires that you use the MUT III to enter a password and follow specific steps to program keys.

As this procedure erases all keys in memory, it is necessary that you have ALL keys available when programming. 

1. Remove the knob from the end of the ignition lock cylinder.
2. Remove the emergency/valet key from ALL F.A.S.T. Key fobs. 
   • For Outlander, insert the first emergency/valet key into the ignition.
   • For Lancer, install the emergency/valet keys into their fobs as shown. Then insert the first E.A.S.T. Key assembly to be registered into the ignition. The assemblies must remin INSIDE the vehicle for the entire process. 
3. Connect the MUT III and turn the ignition key on.
4. From the main menu choose System select. 
5. Select the button From 2006MY. 
6. Click on the car icon at the bottom center of the screen.
7. When the screen changes, select the Auto VIN  icon in the lower right hand corner of the screen. This will fill in the VIN field. If it doesn't, input the VIN using the keyboard,
8. Click the check mark at the bottom of the page. If the CLASS  field was not completed, select the correct class from the pull-down menu. The class is part of the model code. Verify that the VIN and class are correct
9. From the MUT-III System select menu, select F.A.S.T/IMMO/Keyless/TPMS. 
10. If you're working with a Lancer, a Loading Option  window will pop up requesting you select the appropriate combination of features (TPMS, KOS, etc.) for your vehicle. Outlander will skip this step. Make the correct selection from the menu and click the check mark.
11. Select Special Function. 
12. Select Key & F.A.S.T-key Reg. 

    Key Register passwords can be found on the MDL. Select "Service," "Systems," "Vehicle Information." Then select "Key Register Passwords." 

13. Input the Key Register Password. Click on the check mark  at the bottom of the screen. This will register the key in the ignition and you will be asked if you want to register another key.
    NOTE: As each transmitter is registered, you will hear a beep and the number of transmitter IDs registered will increase and be displayed on the MUT-III screen.
14. After the first key has been registered, follow the on-screen instructions. Remove the first key (Outlander) or fob (Lancer) assembly and insert the second key or fob assembly and click the check mark. Repeat the process for all transmitters to be registered.
15. After all keys have been registered, click the cancel button to move on to registering the keyless entry functions.
16. Click on the check mark  at the bottom of the screen.
    NOTE: The following steps must be completed within one minute.
17. Press the lock button twice on each fob to be registered. You will hear a beep and the count on the MUT III screen will increase with each successful registration. Repeat this operation with all fobs.
18. Click on the check mark  at the bottom of the screen.
19. Turn off the ignition and disconnect the MUT III. Verify all functions of the KOS operate properly.

Keyless Entry Registration  - 2007 Outlander, 2008 Lancer without F.A.S.T.-key  . Programming the non-F.A.S.T.-key RKE function  requires that you use the MUT III to enter a password and follow specific steps to program keys.

As this procedure erases ALL transmitters in memory, it is necessary that you have ALL keys available when programming. 

1. Connect the MUT-III, insert the key into the ignition and turn it to the ON position.
2. On the MUT-III main menu, select System select. 
3. Select From 2006MY  then click on the car icon at the bottom of the screen.
4. When the screen changes, select the Auto VIN  icon in the lower right hand corner of the screen. This will fill in the VIN field.
5. Click the check mark  at the bottom of the page. If the CLASS  field was not completed, select the correct class from the pull-down menu. The class is part of the model code.
6. Verify the VIN and class are correct and select the check mark. 
7. Select F.A.S.T./IMMO/Keyless/TPMS  from the System select menu. Then select the check mark at the bottom of the screen.
8. Select Special Function. 
9. Select Keyless ID Reg. 

   Key Register passwords can be found on the MDL. Select "Service," "Systems," "Vehicle Information." Then select "Key Register Passwords." 

10. Input the Key Register Password. Then click on the check mark  at the bottom of the screen.
    NOTE: The following steps must be completed within 4 seconds of clicking the check mark in step  j above.
11. Starting with the key in the ignition, press and hold the lock  and unlock  buttons on the RKE transmitter for approximately one second.
12. Release both the lock  and unlock  buttons for less than 1 second.
13. Press and release the unlock  button.
    NOTE: As each RKE transmitter is registered, the number of Keyless IDs registered will increase and the number of IDs will display on the MUT-III screen.
14. Perform steps m through o above for all other fobs to be registered to the vehicle. A total of eight fobs can be registered.
15. Select the check mark at the bottom of the screen once all RKE transmitters have been registered.
16. Verify the number of Keyless IDs Registered on the MUT-III.
17. Turn the key off, remove it from the ignition and disconnect the MUT-III.
18. Verify all RKE transmitters operate properly.