Specifications Index
GALANT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| (Automatic) | |||
| Service | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Air Conditioning | |||
| (Manual) | |||
| Service | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 226 +/- 29 N.m (167 +/- 21 ft-lb) | ||
| Rear | NA | ||
| Battery | ON-VEHICLE SERVICE | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes (Parking Brake) | |||
| Service Specifications | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes (Parking Brake) | |||
| Service Specifications | GENERAL SPECIFICATIONS . Also refer toPARKING BRAKE LINING AND DRUM | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS . Also refer toPARKING BRAKE LINING AND DRUM | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.4L | Refer to 8. DRIVE BELTS (FOR THE GENERATOR AND POWER STEERING PUMP) (CHECK) | ||
| 3.8L | Refer to 8. DRIVE BELTS (FOR THE GENERATOR AND POWER STEERING PUMP) (CHECK) | ||
| Belt Routing | Refer to 8. DRIVE BELTS (FOR THE GENERATOR AND POWER STEERING PUMP) (CHECK) | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATION | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14 - 18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | |||
| 2.4L | THERMOSTAT | ||
| 3.8L | |||
| Water Pump R & I | |||
| 2.4L | REMOVAL AND INSTALLATION < 2.4L ENGINE > | ||
| 3.8L | REMOVAL AND INSTALLATION < 3.8L ENGINE > | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | Standard value (at engine speed of 250 - 400 RPM): 1,560 kPa (226 psi). Minimum limit (at engine speed of 250 - 400 RPM): 1,130 kPa (164 psi). | ||
| Oil Pressure | Oil pressure at curb idle is 11.4 psi (78 kPa). Oil temperature is 167-194°F (75-90°C). | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.8L | |||
| Compression | Standard value (at engine speed of 200 RPM): 1,550 kPa (225 psi). Minimum limit (at engine speed of 200 RPM): 1,110 kPa (161 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil pressure | Oil pressure at curb idle is 11.6 psi (80 kPa). Oil temperature is 167-194°F (75-90°C). | ||
| Overhaul | SERVICE SPECIFICATIONS (Except MIVEC) or SERVICE SPECIFICATIONS (MIVEC) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (Except MIVEC) or FASTENER TIGHTENING SPECIFICATIONS (MIVEC) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.4L | 167 N.m (123 ft-lb) | ||
| 3.8L | 74 +/- 1 N.m (54 +/- 1 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 324 kPa (47 psi) at curb idle | ||
| Fuel Pressure Test Procedure | Refer to FUEL PRESSURE TEST(2.4L) or FUEL PRESSURE TEST(3.8L) | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.8L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | |||
| 2.4L | See Ignition System Diagram - 2.4L Engine figure under < 2.4L ENGINE > | ||
| 3.8L | < 3.8L ENGINE > | ||
| Spark Plug | |||
| 2.4L | |||
| Type | NGK; LZFR6AI | ||
| Gap | .028-.031 in. (.7-.8 mm) | ||
| Torque | 18 +/- 4 Ft. Lbs. (25 +/- 5 N.m) | ||
| 3.8L | |||
| Type | NGK; FR6EI, DENSO; K20PSR-B8 | ||
| Gap | .028-.031 in. (.7-.8 mm) | ||
| Torque | 18 +/- 4 Ft. Lbs. (25 +/- 5 N.m) | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 Ft. Lbs. (98+/-10 N.m) | ||