Specifications Index
LANCER (Evolution) SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 144 +/- 176 N.m (107 +/- 129 ft-lb) | ||
| Rear | 144 +/- 176 N.m (107 +/- 129 ft-lb) | ||
| Battery | ON-VEHICLE SERVICE | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | See GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS | ||
| Torque | NA | ||
| Drum Brakes (Parking Brake) | |||
| Service Specifications | See GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . Also refer to PARKING BRAKE LINING AND DRUM . | ||
| Torque | NA | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | REMOVAL AND INSTALLATION | ||
| Drive Belts | |||
| Adjustment | 7. DRIVE BELT (FOR THE GENERATOR AND POWER STEERING OIL PUMP) (REPLACE) | ||
| Belt Routing | 7. DRIVE BELT (FOR THE GENERATOR AND POWER STEERING OIL PUMP) (REPLACE) | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14 - 18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 200 RPM): 1,090 kPa (158 psi). Minimum limit (at engine speed of 200 RPM): 650 kPa (95 psi). Difference of all cylinder 100 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more At 3,500 RPM: 294 - 686 kPa (43 - 100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 250 N.m (184 ft-lb) →0 →110 N.m (81 ft-lb) →+60° | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 260 kPa (38 psi) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| Type | NGK; ILKR8E6 | ||
| Gap | 0.020-0.023 in. (0.5-0.6 mm) | ||
| Torque | 18 +/- 2 N.m (13 +/- 1 ft-lb). | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | REMOVAL AND INSTALLATION | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 ft. lbs. (98+/-10 N.m) | ||