LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mitsubishi >> 2009 >> Eclipse GS, Standard >> Repair and Diagnosis >> Brakes >> Traction Control >> Traction Control System (TCL) >> Traction Control System (TCL) Diagnosis >> Diagnostic Trouble Code Procedures >> DTC C1200: Front Right Wheel Speed Sensor (Open Circuit Or Short Circuit) >> Diagnosis
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC C1200: Front Right Wheel Speed Sensor (Open Circuit Or Short Circuit): Diagnosis

Required Special Tools: 

  1. STEP 1. Using scan tool MB991958, diagnose the CAN bus line. 
    CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
    1. Connect scan tool MB991958 to the data link connector.
    2. Turn the ignition switch to the "ON" position.
    3. Diagnose the CAN bus line.
    4. Turn the ignition switch to the "LOCK" (OFF) position.

      Q: Is the CAN bus line found to be normal? 

      YES :  Go to Step  3

      NO :  Repair the CAN bus line (Refer to DIAGNOSIS ). Then go to Step 2.

      Fig 1: Identifying Special Tool MB991910 With Data Link Connector
      G04230562Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  2. STEP 2. Recheck for diagnostic trouble code. 
    CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
    1. Turn the ignition switch to the "ON" position.
    2. Erase the DTC.
    3. Turn the ignition switch to the "LOCK" (OFF) position.
    4. Turn the ignition switch to the "ON" position.
    5. Check if the DTC is set.
    6. Turn the ignition switch to the "LOCK" (OFF) position.

      Q: Is DTC C1200 set? 

      YES :  Go to Step 3

      NO :  The procedure is complete.

      Fig 2: Identifying Special Tool MB991910 With Data Link Connector
      G04230562Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  3. STEP 3. Using scan tool MB991958, check data list. 
    CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
    1. Connect scan tool MB991958 to the data link connector.
    2. Start the engine.
    3. Set scan tool MB991958 to the data reading mode, and check the data list items by driving the vehicle (Refer to DATA LIST REFERENCE TABLE  ).
      • Item 01: Front right wheel speed sensor
    4. Turn the ignition switch to the "LOCK" (OFF) position.

      Q: Does the speedometer indication match the scan tool indication? 

      YES :  Go to Step  10.

      NO :  Go to Step 4.

      Fig 3: Identifying Special Tool MB991910 With Data Link Connector
      G04230562Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  4. STEP 4. Measure the voltage at ABS/TCL-ECU connector A-03. 
    1. Disconnect the connector A-03, and connect special tool MB991997 to the wiring harness-side connector.
      NOTE: Do not connect special tool MB991997 to the ABS/TCL-ECU.
    2. Turn the ignition switch to the "ON" position.
    3. Measure the voltage between terminal 33 and body ground, and between terminal 34 and body ground. It should be 1V or less.

      Q: Does the voltage measure 1 V or less? 

      YES :  Go to Step 5.

      NO :  Go to Step  7.

      Fig 4: Measuring Voltage Between Terminal 33 And Body Ground
      G05892084Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  5. STEP 5. Measure the resistance at ABS/TCL-ECU connector A-03. 
    1. Disconnect the connector A-03, and connect special tool MB991997 to the wiring harness-side connector.
      NOTE: Do not connect special tool MB991997 to the ABS/TCL-ECU.
    2. Measure the resistance between terminal 33 and body ground, and between terminal 34 and body ground. There should be no continuity.

      Q: Does continuity exist? 

      YES :  Go to Step  7.

      NO :  Go to Step 6.

      Fig 5: Measuring Resistance Between Terminal 33 And Body Ground
      G05892084Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  6. STEP 6. Measure the resistance at the ABS/TCL-ECU connector A-03. 
    1. Disconnect the connector A-03, and connect special tool MB991997 to the wiring harness-side connector.
      NOTE: Do not connect special tool MB991997 to the ABS/TCL-ECU.
    2. Measure the resistance between the ABS/TCL-ECU connector terminals 33 and 34.

      Standard Value: 1.24 - 1.64 kΩ 

      Q: Is the resistance between terminals 33 and 34 within the standard value? 

      YES :  Go to Step  10.

      NO :  Go to Step 7.

      Fig 6: Measuring Resistance Between ABS/TCL-ECU Connector Terminals 33 And 34
      G05892086Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  7. STEP 7. Check ABS/TCL-ECU connector A-03 and wheel speed sensor < front: RH > connector A-01 for loose, corroded or damaged terminals, or terminals pushed back in the connector. 

    Q: Are ABS/TCL-ECU connector A-03 and wheel speed sensor < front: RH > connector A-01 damaged? 

    YES :  Repair or replace the damaged component(s). Then go to Step  11.

    NO :  Go to Step 8.

    Fig 7: Identifying Wheel Speed Sensor Front RH Connector A-01
    G05892087Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    Fig 8: Locating ABS/TCL-ECU Connector A-03
    G04232263Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  8. STEP 8. Check the harness wires between ABS/TCL-ECU connector A-03 (terminal 33, 34) and wheel speed sensor connector A-01 (terminal 1, 2). 

    Q: Is the harness wire between ABS/TCL-ECU connector A-03 (terminal 33, 34) and wheel speed sensor connector A-01 (terminal 1, 2) damaged? 

    YES :  Repair the wiring harness. Then go to Step  11.

    NO :  Go to Step 9.

    Fig 9: Identifying Wheel Speed Sensor Front RH Connector A-01
    G05892087Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    Fig 10: Locating ABS/TCL-ECU Connector A-03
    G04232263Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  9. STEP 9. Inspect the wheel speed sensor. 

    Check the front right wheel speed sensor relevant to the DTC code. Repair as necessary.

    Q: Is the wheel speed sensor damaged? 

    YES :  Replace the wheel speed sensor. Then go to Step  11.

    NO :  It can be assumed that this malfunction is intermittent. Refer to HOW TO COPE WITH INTERMITTENT MALFUNCTIONS .

  10. STEP 10. Recheck for diagnostic trouble code. 
    CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.

    Check again if the DTC is set.

    1. Turn the ignition switch to the "ON" position.
    2. Erase the DTC.
    3. Turn the ignition switch to the "LOCK" (OFF) position.
    4. Turn the ignition switch to the "ON" position.
    5. Check if the DTC is reset.
    6. Turn the ignition switch to the "LOCK" (OFF) position.

      Q: Is DTC C1200 set? 

      YES :  Replace the hydraulic unit (integrated with ABS/TCL-ECU). Then go to Step 11.

      NO :  It can be assumed that this malfunction is intermittent. Refer to HOW TO COPE WITH INTERMITTENT MALFUNCTIONS .

      Fig 11: Identifying Special Tool MB991910 With Data Link Connector
      G04230562Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  11. STEP 11. Recheck for diagnostic trouble code. 
    CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
    1. Turn the ignition switch to the "ON" position.
    2. Erase the DTC.
    3. Turn the ignition switch to the "LOCK" (OFF) position.
    4. Turn the ignition switch to the "ON" position.
    5. Check if the DTC is set.
    6. Turn the ignition switch to the "LOCK" (OFF) position.

      Q: Is DTC C1200 set? 

      YES :  Repeat the troubleshooting from Step  1.

      NO :  The procedure is complete.

      Fig 12: Identifying Special Tool MB991910 With Data Link Connector
      G04230562Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
scientia non olet · About LEMON Manuals