LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mitsubishi >> 2011 >> Galant ES >> Repair and Diagnosis (Single Page) >> Transmission >> Automatic Trans >> Automatic Transaxle Diagnosis & On-Vehicle Service >> Transaxle Assembly >> Removal And Installation >> Removal Service Points >> <<E>> Engine Assembly Supporting
April 5, 2026: LEMON Manuals is launched! Read the announcement.

<<E>> Engine Assembly Supporting

  1. < Engine hanger (special tool MB991895) is used>
    1. Set special tool MB991895 (engine hanger) to the front fender assembling bolts (A and B) and (C and D) as shown in illustration.
      Fig 1: Setting Special Tool To Front Fender Assembling Bolts
      G05093258Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. Set special tool MB991527 and MB991454 (chain) to hold the engine/transaxle assembly.
      Fig 2: Holding Engine With Special Tool MB991527 And MB991454
      G05102655Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  2. < Engine hanger (special tool MB991928) is used>
    1. Assemble the engine hanger (special tool MB991928). Set following parts to the base hanger.)
      • SLIDE BRACKET (HI)
      • FOOT (STANDARD) (MB991932) <FRONT SIDE>
      • JOINT (90) (MB991930)
      • FOOT (SHORT) (MB991933) <REAR SIDE>
        Fig 3: Assembling Engine Hanger (Special Tool Mb991928)
        G05102656Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. Set special tool MB991928 (engine hanger) to the front fender assembling bolts (A and B) and (C and D) as shown in illustration.
      Fig 4: Setting Special Tool To Front Fender Assembling Bolts
      G05093258Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    3. Position special tool MB991527 and MB991454 (chain) to hold the engine/transaxle assembly.
      NOTE: Adjust the engine hanger balance by sliding the slide bracket (HI).
      Fig 5: Holding Engine With Special Tool MB991527 And MB991454
      G05102658Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.


  1. Remove the engine hanger.
    Fig 1: Removing Engine Hanger
    G05102675Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  2. After removing the intake manifold plenum stay (rear) and the engine hanger, set special tool MB992012 and MB992013 to each cylinder head.
    Fig 2: Removing Intake Manifold Plenum Stay
    G05093253Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  3. < If engine hanger MB991895 is used>
    1. Set special tool MB991895 (engine hanger) to the front fender assembling bolts (A and B) and (C and D), which are located in the engine compartment, as shown in illustration.
      Fig 3: Setting Special Tool To Front Fender Assembling Bolts
      G05093258Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. Set special tool MB991454 to hold the engine/transaxle assembly.
      Fig 4: Supporting Engine With Garage Jack
      G05102678Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  4. < If engine hanger MB991928 is used>
    1. Assemble the engine hanger (special tool MB991928). Set the following parts to the base hanger.
      • SLIDE BRACKET (HI)
      • FOOT (STANDARD) (MB991932)
      • JOINT (140) (MB991931)
        Fig 5: Installing Special Tool On Hanger
        G05093260Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. Set the engine hanger (special tool MB991928) to the front fender mounting bolts (A and B) and (C and D), which are located in the engine compartment, as shown in illustration.
      NOTE: Adjust the engine hanger balance by sliding the slide bracket (HI).
      Fig 6: Setting Special Tool To Front Fender Assembling Bolts
      G05093258Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    3. Set special tool MB991454 to hold the engine/transaxle assembly.
      Fig 7: Supporting Engine With Garage Jack
      G05093255Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
scientia non olet · About LEMON Manuals