Error Message

WARNING: This page is about a different variant/trim than selected.

When the multivision display detects its own unintentional operation or malfunction in the loaded disk, it displays the following error messages.

ERROR MESSAGES REFERENCE CHART

Error messages	Error contents	Cause	Action
The unit is too hot. Please wait...	Malfunction of multivision display by high temperature	The temperature of HDD inside the multivision display is 201°F (94°C) or more.	Wait until the temperature drops to the operable temperature. After the temperature drops, the error message display is terminated, and then returns to the screen before the error message display.
The unit is too cold. Please wait...	Malfunction of multivision display by low temperature	The temperature of HDD inside the multivision display is -4°F (-20°C) or less.	Wait until the temperature rises to the operable temperature by working the air conditioning. After the temperature rises, the error message display is terminated, and the screen returns to the status before displaying the error message.
It is difficult to read the hard disk. Wait for a while until the hard disk is restored.	Malfunction of HDD by vibration	Severe vibration is applied to the multivision display, and the reading of the HDD data is prohibited.	When the multivision display confirms the HDD data reading availability, it restarts automatically. Check if the multivision display is securely installed to the vehicle body.
	HDD Partition Error	System malfunction occurs to the HDD inside the multivision display.	The multivision display checks HDD automatically. "Restart" is displayed after the completion of the check. Select "Restart" to restart the multivision display. If it does not restart, turn the ignition switch to the OFF position to turn off the power supply, and then turn the ignition switch to the ON position to restart. After the restart, check that the OK is displayed for the HDD Drive in the "Network/Connect Line Check" of the MMCS service mode. If not, replace the multivision display.
Please check the disk.	Disk type error	The specification of the disk used has a problem.	The disk used may have a problem. Check the disk for scratches or dirt. Also, perform the Inspection procedure 8 "CD/DVD cannot be Played" of the troubleshooting. (Refer to INSPECTION PROCEDURE 8: CD/DVD CANNOT BE PLAYED. .)
Play is impossible due to a focus error. Please eject the disk.	Focus error	The disk used has scratches and dirt, and the data cannot be read.
Play is impossible. Please eject the disk.	Disk error	The data of the disk used has a malfunction, and the data cannot be read.
	Seek error
	Servo startup error
	TOC read error
	DVD-Video Disk info error (Disk information cannot be read.)
Play is impossible due to a Mechanism error.	Power-on error	The DVD drive inside the multivision display has a malfunction.	Perform the Inspection procedure 8 "CD/DVD cannot be Played" of the troubleshooting. (Refer to INSPECTION PROCEDURE 8: CD/DVD CANNOT BE PLAYED. .)
	Pickup operation error
	Mecha stack error
	Loading/eject error
The region code is incorrect. Please eject the disk.	DVD-Video region code error	The region code of the DVD does not match the specification of the multivision display.	Replace with the DVD that matches the specification of the multivision display.
Please eject the disk. The monitor panel is too hot. Screen display has stopped to protect the liquid crystal panel. Wait until the monitor panel has cooled down.	Monitor high temperature error	The temperature of the monitor is 203°F (95°C) or more for 60 seconds or more.	The monitor turns OFF 5 seconds after the error message appears. Wait until the temperature of the monitor drops. The temperature drops, and then the multivision display returns automatically.

NOTE: "Environment" is not displayed on the "INFO" screen. Ambient temperature is not displayed on the environment screen. If atmospheric pressure or altitude is not displayed on the environment display, the CAN box unit may have a problem in the CAN communication with A/C-ECU or engine control module. Check if a diagnostic trouble code is set in the CAN box unit.