Common Specs & Procedures
LANCER EVOLUTION COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Automatic | N/A | ||
| Manual | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 144-176 N.m (107-129 ft-lb) | ||
| Rear | 144-176 N.m (107-129 ft-lb) | ||
| Battery | BATTERY - LANCER EVOLUTION | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | See figure in REMOVAL AND INSTALLATION for Front Disc Brake Assembly, REMOVAL AND INSTALLATION for Rear Disc Brake Assembly | ||
| Drum Brakes (Parking Brake) | |||
| Service Specifications | SERVICE SPECIFICATIONS and PARKING BRAKE LINING AND DRUM . | ||
| Torque | PARKING BRAKE LINING AND DRUM | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | Refer to figure in REMOVAL AND INSTALLATION . | ||
| Drive Belts | |||
| Adjustment | Refer to DRIVE BELT TENSION CHECK and AUTO-TENSIONER CHECK . | ||
| Belt Routing | Refer to figure in FUNCTION CHECK . | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | Standard value: 93-123 kPa (14-18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 200 RPM): 1, 090 kPa (158 psi). Minimum limit (at engine speed of 200 RPM): 750 kPa (109 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more: At 3, 500 RPM: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 1st Step: 30 ft. lbs. (40 N.m); 2nd Step: 96 ft. lbs. (130 N.m) | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 260 kPa (38 psi) at curb idle. | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | N/A | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plug | |||
| Type | NGK; DILKR8B6 | ||
| Gap | Standard Value: 0.5-0.6 mm (0.020-0.023 in.); Limit: 0.8 mm (0.031 in.) | ||
| Torque | 18 ± 2 N.m (13 ± 1 ft-lb) | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | See figure in STARTER MOTOR ASSEMBLY . | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 ft. lbs. (98+/-10 N.m) | ||