Torque Specifications
WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS
| Item | Specification |
|---|---|
| Clutch Housing Case Assembly | |
| Roll stopper bracket | 90 ± 10 N.m (66 ± 7 ft-lb) |
| Vehicle speed sensor | 10 ± 2 N.m (89 ± 17 in-lb) |
| Wiring harness clamp bracket | 17.0 ± 6.8 N.m (13 ± 4 ft-lb) |
| Transaxle case hanger No. 1 | 17.0 ± 6.8 N.m (13 ± 4 ft-lb) |
| Reverse shift arm bracket assembly | 17.0 ± 5.1 N.m (13 ± 3 ft-lb) |
| Gear shift fork assembly No. 2 | 24.0 ± 4.8 N.m (18 ± 2 ft-lb) |
| Gear shift head No. 1 | 24.0 ± 4.8 N.m (18 ± 2 ft-lb) |
| Gear shift fork assembly No. 1 | 24.0 ± 4.8 N.m (18 ± 2 ft-lb) |
| Transaxle case receiver | 7.0 ± 2.8 N.m (62 ± 24 in-lb) |
| Transaxle Case Assembly | |
| Backup light switch | 40 ± 16 N.m (30 ± 11 ft-lb) |
| Lock ball assembly | 29.0 ± 8.7 N.m (21 ± 5 ft-lb) |
| Backup light switch wiring harness clamp | 7.5 ± 2.3 N.m (66 ± 20 in-lb) |
| Control cable bracket | 17.0 ± 6.8 N.m (13 ± 4 ft-lb) |
| Lever lock pin mounting nut | 11.8 ± 3.5 N.m (106 ± 26 in-lb) |
| Control shift lever connecting nut | 11.8 ± 3.5 N.m (106 ± 26 in-lb) |
| Selecting bell crank assembly and control bell crank dust cover mounting bolt | 24.5 ± 9.8 N.m (18 ± 6 ft-lb) |
| Control shaft cover | 20 ± 8 N.m (15 ± 5 ft-lb) |
| Clutch tube bracket | 50 ± 5 N.m (37 ± 3 ft-lb) |
| Transaxle case cover sub assembly mounting bolt | 29.0 ± 8.7 N.m (21 ± 5 ft-lb) |
| Gear shift fork assembly No. 3 | 24.0 ± 4.8 N.m (18 ± 2 ft-lb) |
| 5th drive gear mounting nut | 123 ± 36.9 N.m (91 ± 26 ft-lb) |
| Rear bearing retainer | 42.0 ± 8.4 N.m (31 ± 5 ft-lb) |
| Reverse idler shaft mounting bolt | 30 ± 9 N.m (22 ± 6 ft-lb) |
| Clutch housing case mounting bolt | 29.0 ± 5.8 N.m (21 ± 3 ft-lb) |
| Oil receiver pipe | 17.0 ± 6.8 N.m (13 ± 4 ft-lb) |
| With head straight screw plug | 13.0 ± 5.2 N.m (115 ± 44 in-lb) |
| Select shaft lever nut | 12 ± 3 N.m (106 ± 26 in-lb) |
| Select lever shaft nut | 12 ± 3 N.m (106 ± 26 in-lb) |
| Differential Case | |
| Ring gear | 106 ± 6.4 N.m (78 ± 4 ft-lb) |