Service Specifications
WARNING: This page is about a different variant/trim than selected.
| Item | Standard value | Limit | |
|---|---|---|---|
| Timing chain | |||
| Valve clearance mm (in) | Intake | 0.20 ± 0.03 (0.008 ± 0.001) | - |
| Exhaust | 0.30 ± 0.03 (0.012 ± 0.001) | - | |
| Camshaft | |||
| Cam height of camshaft mm (in) | Intake | 44.1 (1.74) | 43.6 (1.72) |
| Exhaust | 45.0 (1.77) | 44.5 (1.75) | |
| Camshaft oil clearance mm (in) | 0.035 - 0.072 (0.0014 - 0.0028) | - | |
| Cylinder head and valves | |||
| Distortion of cylinder head bottom mm (in) | Within 0.05 (0.002) | 0.2 (0.01) | |
| Grinding limit of cylinder head bottom mm (in) | - | 0.2 (0.01) | |
| Overall height of cylinder head mm (in) | 128.5 (5.06) | - | |
| Overall length of valve mm (in) | Intake | 113.18 (4.456) | 112.68 (4.436) |
| Exhaust | 105.89 (4.169) | 105.39 (4.149) | |
| Valve margin mm (in) | Intake | 1.022 (0.0402) | 0.522 (0.0206) |
| Exhaust | 1.094 (0.0431) | 0.594 (0.0234) | |
| Free height of valve spring mm (in) | 51.5 (2.03) | 51.0 (2.01) | |
| Squareness of valve spring | 2° or less | 4° | |
| Clearance between valve guide and valve stem mm (in) | Intake | 0.020 - 0.047 (0.0008 - 0.0019) | 0.10 (0.004) |
| Exhaust | 0.030 - 0.057 (0.0012 - 0.0022) | 0.15 (0.006) | |
| Valve seat contact width mm (in) | Intake | 1.16 - 1.46 (0.046 - 0.058) | - |
| Exhaust | 1.35 - 1.65 (0.053 - 0.065) | - | |
| Oversize rework dimensions of valve guide hole mm (in) | 0.25 oversize diameter | 11.23 - 11.25 (0.442 - 0.443) | - |
| Intake oversize rework dimensions of valve seat hole mm (in) | 0.3 oversize diameter | 36.22 - 36.24 (1.426 - 1.427) | - |
| Exhaust oversize rework dimensions of valve seat hole mm (in) | 0.3 oversize diameter | 30.22 - 30.24 (1.190 - 1.191) | - |
| Oil pump chain | |||
| Oil cooler by-pass valve dimension "L" mm (in) | 34.5 (1.358) | 40.0 (1.575) | |
| Piston and connecting rod | |||
| Clearance between piston ring and ring groove mm (in) | No. 1 | 0.02 - 0.06 (0.001 - 0.002) | 0.10 (0.004) |
| No. 2 | 0.02 - 0.06 (0.001 - 0.002) | 0.10 (0.004) | |
| Piston ring end gap mm (in) | No. 1 | 0.18 - 0.28 (0.007 - 0.011) | 0.8 (0.03) |
| No. 2 | 0.28 - 0.43 (0.011 - 0.017) | 0.8 (0.03) | |
| Oil | 0.10 - 0.34 (0.004 - 0.013) | 1.0 (0.04) | |
| Clearance of connecting rod big end thrust mm (in) | 0.10 - 0.25 (0.004 - 0.010) | 0.4 (0.02) | |
| Outside diameter of connecting rod bolt mm (in) | - | 0.10 (0.004) | |
| Connecting rod bearing oil clearance mm (in) | 0.038 - 0.069 (0.0015 - 0.0027) | 0.10 (0.004) | |
| Crankshaft and cylinder block | |||
| Out side diameter clearance of crankshaft bearing cap bolt mm (in) | M8 | - | 0.10 (0.004) |
| M10 | - | 0.15 (0.006) | |
| Crankshaft end play mm (in) | 0.05 - 0.25 (0.002 - 0.010) | 0.4 (0.02) | |
| Crankshaft journal oil clearance mm (in) | No. 1, 2, 4, 5 | 0.039 - 0.065 (0.0015 - 0.0026) | 0.10 (0.004) |
| No. 3 | 0.051 - 0.077 (0.0020 - 0.0030) | 0.10 (0.004) | |
| Distortion of cylinder block top surface mm (in) | - | 0.05 (0.002) | |
| Grinding limit of cylinder block top surface mm (in) | - | 0.2 (0.01) | |
| Cylinder block cylinder bore mm (in) | 86 (3.4) | - | |
| Cylindricity of cylinder block mm (in) | 0.010 (0.0004) | - | |