Common Specs & Procedures
LANCER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 250 ± 25 (184 ± 18 ft-lb) | ||
| Rear (FWD) | 95 ± 14 N.m (70 ± 10 ft-lb) | ||
| Rear (AWD) | 144-176 N.m (107-129 ft-lb) | ||
| Battery | SERVICE SPECIFICATIONS , BATTERY CHARGING | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Charging | |||
| Generator | GENERAL INFORMATION and SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | DRIVE BELT TENSION CHECK | ||
| 2.4L | DRIVE BELT TENSION CHECK | ||
| Belt Routing | |||
| 2.0L | DRIVE BELT INSTALLATION | ||
| 2.4L | DRIVE BELT INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS , COOLANT | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14-18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | REMOVAL AND INSTALLATION | ||
| Engine Mechanical 2.0L | |||
| Compression | Standard value (at engine speed of 200 RPM): 1,470 kPa (213 psi). Minimum limit (at engine speed of 200 RPM): 1050 kPa (152 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more At 3, 500 RPM: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Engine Mechanical (2.4L) | |||
| Compression | Standard value (at engine speed of 200 RPM): 1,440 kPa (209 psi). Minimum limit (at engine speed of 200 RPM): 1000 kPa (145 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more At 3,500 RPM: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 40 N.m (30 ft-lb) → 130 N.m (96 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 324 kPa (47 psi) at curb idle | ||
| Fuel Pressure Test Procedure | |||
| 2.0L | FUEL PRESSURE TEST | ||
| 2.4L | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT 2.0L , 2.4L (FWD) FUEL PUMP MODULE REPLACEMENT 2.4L (AWD) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug 2.0L | |||
| Type | NGK; DIFR6C11 | ||
| Gap | Standard Value: 0.039-0.043 in. (1.0-1.1 mm). Limit: 0.051 in. (1.3 mm) | ||
| Torque | 25 +/- 5 N.m (18 +/- 3 ft-lb). | ||
| Spark Plug (2.4L) | |||
| Type | NGK; DIFR5C11 | ||
| Gap | Standard Value: 0.039-0.043 in. (1.0-1.1 mm). Limit: 0.051 in. (1.3 mm) | ||
| Torque | 25 +/- 5 N.m (18 +/- 3 ft-lb). | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 ft. lbs. (98+/-10 N.m) | ||