LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mitsubishi >> 2019 >> Eclipse Cross SP >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Fuel Supply >> On-Vehicle Service >> Fuel Pump (Module) Replacement
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Fuel Pump (Module) Replacement

  1. Remove the rear seat assembly (Refer to REAR SEAT ASSEMBLY ).
  2. Remove the floor inspection lid (LH).
    G10222593Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  3. Disconnect the fuel pump and gauge assembly connector.
  4. Release the fuel pressure in the fuel line (Refer to REDUCE PRESSURIZED FUEL LINES ).
    G12144317Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  5. Insert a flat-tip screwdriver (6 mm (0.2 inch) wide and 1 mm (0.04 inch) thick) into the retainer of the fuel main pipe connector.
    G12144318Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    CAUTION: When pushing up the retainer of the fuel main pipe connector, pay attention to avoid damage to the retainer.
  6. Turn the flat-tip screwdriver inserted into the retainer by 90 degrees to push up the retainer and unlock the fuel main pipe connector.
    G12144319Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  7. Remove the mounting nuts of fuel pump and gauge assembly.
  8. Remove the fuel pump bracket plate.
    CAUTION: Pay attention not to damage the gauge unit and the float of fuel pump and gauge assembly when withdrawing it from the service hole.
  9. Remove the fuel pump and gauge assembly from the service hole <FWD>.
    NOTE: For disassembly and reassembly of the fuel pump and gauge assembly, refer to DISASSEMBLY AND ASSEMBLY .
    G12144320Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    CAUTION: Pay attention not to damage the gauge unit and the float of fuel pump and gauge assembly when withdrawing it from the service hole.
  10. While withdrawing the fuel pump and gauge assembly from the service hole, disconnect the suction hose from the fuel pump and gauge assembly to remove the fuel pump and gauge assembly from the service hole completely <FWD>.
    NOTE: For disassembly and reassembly of the fuel pump and gauge assembly, refer to DISASSEMBLY AND ASSEMBLY .
  11. Replace the fuel pump and gauge assembly gasket with a new one.
    G10222940Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    CAUTION:
    • Pay attention not to damage the gauge unit and the float of fuel pump and gauge assembly when installing it to the fuel tank from the service hole.
    • When installing the fuel pump and gauge assembly to the fuel tank, check that the gauge moving area moves smoothly.
  12. Install the fuel pump and gauge assembly to the fuel tank through the service hole <FWD>.
    CAUTION:
    • Pay attention not to damage the gauge unit and the float of fuel pump and gauge assembly when installing it to the fuel tank from the service hole.
    • Pay attention to prevent the float of fuel pump and gauge assembly from being trapped by the suction hose inside the fuel tank.
    • When installing the fuel pump and gauge assembly to the fuel tank, check that the gauge moving area moves smoothly.
  13. While inserting the fuel pump and gauge assembly into the fuel tank from the service hole, connect the suction hose to the fuel pump and gauge assembly to install the fuel pump and gauge assembly to the fuel tank <FWD>.
  14. Install the fuel pump bracket plate.
    G10222940Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  15. Tighten the fuel pump and gauge assembly mounting nuts to the specified torque.

    Tightening torque: 2.5 ± 0.4 N.m (22 ± 3 in-lb) 

    G12144320Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  16. Pull up the retainer of fuel main pipe to unlock before installing.
    G10222943Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    CAUTION:
    • When pushing in the retainer of the fuel main pipe connector, pay attention to avoid damage to the retainer.
    • After the installation of the fuel main pipe, slightly pull the fuel main pipe to check that it is connected securely. At this time, also check that there is approximately 1 mm play.
  17. Install the fuel main pipe to the fuel pump and gauge assembly securely and push in the retainer of the fuel main pipe connector to lock the fuel main pipe and fuel pump and gauge assembly.
    G12144325Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  18. Connect the fuel pump and gauge assembly connector.
    G12144317Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  19. Install the floor inspection lid (LH).
  20. Return the floor carpet to the original condition and install the rear seat assembly (Refer to REAR SEAT ASSEMBLY ).
    G10222593Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
scientia non olet · About LEMON Manuals