| TIMING CHAIN |
| Valve clearance mm (in) |
Inlet |
0.22 ± 0.04 (0.009 ± 0.002) |
- |
| Exhaust |
0.30 ± 0.04 (0.012 ± 0.002) |
- |
| CAMSHAFT |
| Cam height mm (in) |
Inlet |
44.71 (1.760) |
44.21 (1.741) |
| Exhaust |
44.18 (1.739) |
43.68 (1.720) |
| CYLINDER HEAD AND VALVES |
| Outside diameter difference of cylinder head bolt mm (in) |
- |
0.15 (0.006) |
| Cylinder head bottom face distortion mm (in) |
0.03 (0.001) or less |
- |
| Cylinder head overall height mm (in) |
112.9 - 113.1 (4.445 - 4.452) |
- |
| Valve margin mm (in) |
Inlet |
0.85 (0.033) |
0.70 (0.028) |
| Exhaust |
1.5 (0.06) |
1.35 (0.053) |
| Valve face angle |
45° - 45.5° |
- |
| Valve stem-to-guide clearance mm (in) |
Inlet |
0.020 - 0.047 (0.0008 - 0.0018) |
0.10 (0.004) |
| Exhaust |
0.041 - 0.068 (0.0017 - 0.0026) |
0.15 (0.006) |
| Valve length mm (in) |
Inlet |
87.21 (3.433) |
86.71 (3.414) |
| Exhaust |
88.54 (3.486) |
88.04 (3.466) |
| Valve spring free length mm (in) |
52.20 (2.055) |
43.1 (1.70) |
| Valve spring out-of-squareness |
2° or less |
4° |
| Valve seat contact width mm (in) |
1.1 - 1.5 (0.044 - 0.059) |
- |
| PISTON AND CONNECTING ROD |
| Piston outer diameter mm (in) |
75 (3.0) |
- |
| Piston ring to ring groove clearance mm (in) |
No. 1 |
0.04 - 0.075 (0.0016 - 0.0029) |
0.1 (0.004) |
| No. 2 |
0.04 - 0.08 (0.002 - 0.003) |
0.1 (0.004) |
| Piston ring end gap mm (in) |
No. 1 |
0.25 - 0.30 (0.010 - 0.011) |
0.8 (0.03) |
| No. 2 |
0.40 - 0.55 (0.016 - 0.021) |
0.8 (0.03) |
| Oil ring |
0.25 - 0.45 (0.010 - 0.017) |
1.0 (0.04) |
| Crankshaft pin oil clearance mm (in) |
0.020 - 0.038 (0.0008 - 0.0014) |
0.1 (0.004) |
| Outside diameter difference of connecting rod bolt mm (in) |
- |
0.1 (0.004) |
| Connecting rod big end thrust clearance mm (in) |
0.10 - 0.35 (0.004 - 0.013) |
0.4 (0.02) |
| CRANKSHAFT AND CYLINDER BLOCK |
| Crankshaft bearing cap bolt shank length mm (in) |
- |
75.3 (2.96) |
| Crankshaft end play mm (in) |
0.09 - 0.27 (0.004 - 0.010) |
0.3 (0.01) |
| Crankshaft journal oil clearance mm (in) |
0.014 - 0.034 (0.0006 - 0.0013) |
0.1 (0.004) |
| Cylinder block top surface distortion mm (in) |
0.05 (0.002) |
0.1 (0.004) |
| Cylinder block top face grinding limit (Total resurfacing depth of both cylinder head and cylinder block) mm (in) |
- |
0.2 (0.01) |
| Cylinder block overall height mm (in) |
279.59 (11.007) |
- |
| Cylinder bore mm (in) |
75 (3.0) |
- |
| Cylindrically mm (in) |
0.01 (0.0004) or less |
- |