Common Specs & Procedures
OUTLANDER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | See GENERAL INFORMATION and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 250 ± 25 N.m (184 ± 18 ft. lb.) | ||
| Rear - FWD | 95 ± 14 N.m (70 ± 10 ft. lb.) | ||
| Rear - AWD | 250 ± 25 N.m (184 ± 18 ft. lb.) | ||
| Battery | See GENERAL INFORMATION and BATTERY CHARGING . | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SERVICE SPECIFICATIONS | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Charging | |||
| Generator | See GENERATOR SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Drive Belts | |||
| Adjustment | |||
| 2.4L | DRIVE BELT TENSION CHECK | ||
| 3.0L | GENERATOR DRIVE BELT TENSION CHECK | ||
| Drive Belt Routing | |||
| 2.4L | Refer to Drive Belt And Pulley System Diagram figure under DRIVE BELT INSTALLATION | ||
| 3.0L | NA | ||
| Engine Cooling | |||
| General Service Specifications | See SERVICE SPECIFICATIONS and COOLANT . | ||
| Radiator Cap Pressure | Standard value: 93-123 kPa (14-18 psi); Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | |||
| 2.4L | REMOVAL AND INSTALLATION | ||
| 3.0L | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | |||
| 2.4L | REMOVAL AND INSTALLATION | ||
| 3.0L | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | Standard value (at engine speed of 200 r/min): 1,180 kPa (171 psi): Minimum limit 800 kPa (116 psi); differences of the cylinders: Limit: 150 kPa (22 psi) | ||
| Oil Pressure | Engine oil pressure: at idle: 29 kPa (4.2 psi) or more; at 3500 r/min: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.0L | |||
| Compression | Standard value (at engine speed of 200 r/min): 1,650 kPa (239 psi); Minimum limit: 1,150 kPa (167 psi); differences of the cylinders: Limit: 100 kPa (15 psi) | ||
| Oil pressure | Engine oil pressure: at idle: 29 kPa (4.2 psi) or more; at 3500 r/min: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.4L | Step 1: 40 N.m (30 ft. lb.); Step 2: 130 N.m (96 ft. lb.). | ||
| 3.0L | 76 ± 4 N.m (56 ± 2 ft. lb.) | ||
| Fuel System | |||
| Pressure Specification | 324 kPa (47 psi) at curb idle | ||
| Fuel Pressure Test Procedure | |||
| 2.4L | FUEL PRESSURE TEST | ||
| 3.0L | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module, which is located in fuel tank. | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | See FIRING ORDER & CYLINDER IDENTIFICATION article. | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 2.4L | |||
| Type | NGK DILKR6D11G | ||
| Gap | Standard: 1.0-1.1 mm (0.039-0.043 in.); Limit: 1.3 mm (0.051 in.) | ||
| Torque | 25 ± 5 N.m (18 ± 3 ft. lb.) | ||
| 3.0L | |||
| Type | NGK DILKR7C11 | ||
| Gap | Standard: 1.0-1.1 mm (0.039-0.043 in.); Limit: 1.3 mm (0.051 in.) | ||
| Torque | 18 ± 2 N.m (13 ± 1 ft. lb.) | ||
| Starting | |||
| Starter | See STARTER MOTOR SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are included in article figures. | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 98 ± 10 N.m (73 ± 7 ft. lb.) | ||